# $Id: format.dat,v 2.18 1997/06/25 18:58:34 jdd Exp $ # # Maintained by John DiMarco (jdd@cdf.toronto.edu) # University of Toronto, CDF # # based on one dated October 5, 1992 by George Neville-Neil DEC WSL # (gnn@cs.berkeley.edu) # # This file was built using a base format.dat file and added to using # format.dat entries mailed in from various people on the Internet. # # DISCLAIMER: This is provided as a public service to sun managers. Neither # I nor anyone else guarantees the correctness of these entries. # # All attempts have been made to eliminate duplicate information. # # Most of the comments came from the suppliers of the data and are not # mine. # # If you come across any errors or wish to add new entries, please send # email to: sun-managers-format@eecs.nwu.edu # # This file is available for anonymous ftp from ra.mcs.anl.gov in # /sun-managers/format.dat. # # If the drive you want isn't here, you can contact the manufacturer. # Some manufacturers run Bulletin Board systems: # # Fujitsu America BBS 408 944 9899 # Seagate BBS USA/Can 408 438 8771 # Seagate BBS England 44 62 847 8011 # Seagate BBS Germany 49 89 140 9331 # Seagate BBS Singapore 65 292 6973 # Seagate BBS Australia 61 2 756 2359 # Maxtor BBS 303 678 2222 # Micropolis BBS 818 709 3310 # Quantum BBS 408 894 3214 # Conner BBS 408 456 4415 / 408 456 3200 # Western Digital 714 932 4900 # # It is also possible to contact drive manufacturers by telephone. # Some relevant numbers are: # # Fujitsu USA 800-626-4686 # 408-432-1300 # Fujitsu FAXLINE 408-428-0456 # Fujitsu Canada 416-602-5454 # 800-263-7091 # HP USA 800-826-4111 # HP mass storage 970-635-1000 # Hitachi USA 800-HIT-ACHI # Hitachi HITFAX 800-HIT-FAX1 # Maxtor USA 800-2MA-XTOR # Maxtor FAXBACK 303-678-2618 # Maxtor Auto 800-262-9867 # Micropolis USA 818-709-3300 # Micropolis Tech 818-709-3325 # Seagate USA 800-468-3472 # 408-438-8222 # Seagate FAX 408-438-8137 # Seagate FAXBACK 408-438-2620 # Quantum USA 800-826-8022 # Conner USA 408-456-3247 # 408-456-4500 # Conner Auto 800-421-1879 # Conner Tech 800-426-6637 # Conner FAXBACK 408-456-4903 # Conner Service 800-537-2248 # # CDC spun off their disk-drive business as Imprimis, which was later bought # by Seagate, so direct all questions about CDC and Imprimis drives to Seagate. # # Fujitsu lists some format parameters for their drives on the WWW, at # http://www.fujitsu-europe.com/t_sun01.htm # # Quantum lists some format parameters for their drives on the WWW, at # http://support.quantum.com/appnotes/sun.htm # # TIPS for rolling your own format.dat # # In SunOS 5.3 (aka Solaris 2.3) and later, the format program supports the # automatic querying of SCSI drives for their parameters, and a format.dat # entry is not strictly necessary. # # For SCSI disks, any combination of cylinders, heads and sectors that does # not add up to more than the rated formatted capacity of the drive # will usually work, because the SCSI specification hides most of the drive # details from the host. # # A program which queries a SCSI drive for its parameters and generates a # format.dat entry for it is scsiinfo, which is available for anonymous # ftp from ftp.cdf.toronto.edu (128.100.31.2):/pub/scsiinfo/scsiinfo-*.shar. # [ Yes, it's an attempt to put myself out of the format faq business. :-) ] # Moreover, SCSI drives may be queried at great length using the scsiping # program, which is freely available for anonymous ftp from # ftp.cdf.toronto.edu (128.100.31.2) and ftp.fwi.uva.nl (146.50.4.20) in # /pub/scsiping/scsiping-2.0.shar. # # woods@most.weird.com (Greg A. Woods) makes the following suggestions # for finding geometry information if it's not here, and if you can't run # scsiping or scsiinfo: # # 1. run format and choose the "Other type" disk # # 2. supply reasonable values for the disk geometry # # 3. go back to the main menu and enter the defect mananagement menu and # load the "original manufacturer's defect list", then commit the list # # 3a. optionally print the defect list to get clues on the geometry and go # back to step 1. # # 4. enter the "analysis" menu and run the "setup" option to turn *on* the # "extended messages" (and optionally set other values, such as number of # passes to one) # # 5. go back to the main menu and format the drive # # If you didn't get all the geometry right, the extended messages printed # will show the correct values (according to the drive) in parenthesis # after the values you did enter. Run format again and enter the correct # geometry, or write a new /etc/format.dat entry. # # For SunOS 4.1.2 and earlier, replace all occurrences of "SCSI" by "MD21". # For SunOS 5.x, replace partition names a, b, c, etc. with 0, 1, 2, etc. # For Solbourne systems, replace all occurrences of "SCSI" by "IOASIC". # # When partitioning, do not make a partition larger than 2GB (2097152 KB, or # 4194304 blocks), since SunOS does not support partitions larger than 2GB. # # This is the search path for 'format'. It contains all the disks that # will be searched for if no disk list is given on the command line. # search_path = xd0, xd1, xd2, xd3, xd4, xd5, xd6, xd7, xd8, xd9, xd10, xd11, \ xd12, xd13, xd14, xd15, xy[0-3], sd[0-7], sd8, sd9, sd10, \ sd11, sd12, sd13, sd14, sd15, id0[0-3][0-7] # # This is the list of supported disks for the Xylogics 450/451 controller. # disk_type = "Fujitsu-M2312K" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 587 : acyl = 2 : pcyl = 589 : nhead = 7 : nsect = 32 \ : rpm = 3600 : bpt = 20480 : bps = 621 : drive_type = 1 disk_type = "Fujitsu-M2284/M2322" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 821 : acyl = 2 : pcyl = 823 : nhead = 10 : nsect = 32 \ : rpm = 3600 : bpt = 20480 : bps = 621 : drive_type = 2 disk_type = "Fujitsu-M2351 Eagle" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 840 : acyl = 2 : pcyl = 842 : nhead = 20 : nsect = 46 \ : rpm = 3961 : bpt = 28160 : bps = 595 : drive_type = 0 disk_type = "Fujitsu-M2333" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 821 : acyl = 2 : pcyl = 823 : nhead = 10 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 : drive_type = 3 disk_type = "Fujitsu-M2361 Eagle" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 840 : acyl = 2 : pcyl = 842 : nhead = 20 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 : drive_type = 3 disk_type = "CDC EMD 9720" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 1147 : acyl = 2 : pcyl = 1217 : nhead = 10 : nsect = 48 \ : rpm = 3600 : bpt = 30240 : bps = 613 : drive_type = 1 disk_type = "Hitachi DK815-10" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 1735 : acyl = 2 : pcyl = 1737 : nhead = 15 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 : drive_type = 1 disk_type = "NEC D2363" \ : ctlr = XY450 : fmt_time = 4 \ : ncyl = 964 : acyl = 2 : pcyl = 1024 : nhead = 27 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 : drive_type = 2 # # This is the list of supported disks for the Xylogics 7053 controller. # disk_type = "Fujitsu-M2351 Eagle" \ : ctlr = XD7053 \ : ncyl = 840 : acyl = 2 : pcyl = 842 : nhead = 20 : nsect = 46 \ : rpm = 3961 : bpt = 28160 : bps = 595 disk_type = "Fujitsu-M2333" \ : ctlr = XD7053 \ : ncyl = 821 : acyl = 2 : pcyl = 823 : nhead = 10 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 disk_type = "Fujitsu-M2361 Eagle" \ : ctlr = XD7053 \ : ncyl = 840 : acyl = 2 : pcyl = 842 : nhead = 20 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 disk_type = "CDC EMD 9720" \ : ctlr = XD7053 \ : ncyl = 1147 : acyl = 2 : pcyl = 1217 : nhead = 10 : nsect = 48 \ : rpm = 3600 : bpt = 30240 : bps = 613 disk_type = "Hitachi DK815-10" \ : ctlr = XD7053 \ : ncyl = 1735 : acyl = 2 : pcyl = 1737 : nhead = 15 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 disk_type = "NEC D2363" \ : ctlr = XD7053 \ : ncyl = 964 : acyl = 2 : pcyl = 1024 : nhead = 27 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 disk_type = "Fujitsu-M2372K" \ : ctlr = XD7053 \ : ncyl = 743 : acyl = 2 : pcyl = 745 : nhead = 27 : nsect = 67 \ : rpm = 3600 : bpt = 40960 : bps = 600 disk_type = "CDC 9720-850" \ : ctlr = XD7053 \ : ncyl = 1358 : acyl = 2 : pcyl = 1360 : nhead = 15 : nsect = 66 \ : rpm = 3600 : bpt = 41088 : bps = 610 # # From megatek!randy@suntan.West # # works great on a 4/300 disk_type = "Sabre ST82500J" \ : ctlr = XD7053 \ : ncyl = 2609 : acyl = 2 : pcyl = 2611 : nhead = 19 : nsect = 82 \ : rpm = 3600 : bpt = 50400 : bps = 604 # # From: "Adam W. Feigin" # # We recently decomissioned a couple of Alliant FX/80's which had these # drives in them. Between for formatting program on the Alliant, and the # Fujitsu manual, I came up with the following format.dat entry. We've been # using this entry on the dozen or so drives we pulled from our Alliants # for about 6 months now without any problems. The drive formats down to # roughly 525MB with this entry.... disk_type = "Fujitsu M2344K" \ : ctlr = XD7053 \ : ncyl = 622 : acyl = 2 : pcyl = 624 : nhead = 27 : nsect = 64 \ : rpm = 3600 : bpt = 40960 : bps = 600 # Format.dat 1.26 of 89/09/06, from a 490, shows Sun support of the # following Imprimis drives on either the SMD-4 or ISP-80 (Sun IPI-2) # controllers: # The 3 disks shown are, respectively, the Sabre 9720-368, 9720-850, # and 9720-1230. disk_type = "CDC EMD 9720" \ : ctlr = XD7053 \ : ncyl = 1147 : acyl = 2 : pcyl = 1217 : nhead = 10 : nsect = 48 \ : rpm = 3600 : bpt = 30240 : bps = 613 disk_type = "CDC 9720-850" \ : ctlr = XD7053 \ : ncyl = 1358 : acyl = 2 : pcyl = 1360 : nhead = 15 : nsect = 66 \ : rpm = 3600 : bpt = 41088 : bps = 610 # From: Tom Limoncelli # # Seagate Sabre-5 ST81236J drive # used with the Xylogics 7053 controller disk_type = "Seagate Sabre-5 ST81236J" \ : ctlr = XD7053 \ : ncyl=1633: acyl= 2: pcyl=1635: nhead=15: nsect=82 \ : rpm=3600 : bpt=50400 : bps=604 partition = "Seagate Sabre-5 ST81236J" \ : disk = "Seagate Sabre-5 ST81236J" : ctlr = XD7053 \ : a = 0, 99630 : b = 81, 261990 : c = 0, 2008590 \ : d = 294, 548580 : e = 740, 1098390 : f = 0, 361620 \ : g = 294, 1646970 : h = 81, 1908960 # From: Tom Limoncelli # Fujitsu-M2382 on a Xylogics-7053 (/dev/xd*) controller. disk_type = "Fujitsu-M2382" \ : ctlr = XD7053 \ : ncyl = 743 : acyl = 2 : pcyl = 745 : nhead = 27 : nsect = 81 \ : rpm = 3600 : bpt = 49728 : bps = 604 partition = "Fujitsu-M2382" \ : disk = "Fujitsu-M2382" :ctlr = XD7053 \ : a = 0, 80919 : b = 37, 129033 : c = 0, 1624941 \ : d = 96, 470205 : e = 311, 944784 : f = 0, 209952 \ : g = 96, 1414989 : h = 37, 1544022 # From johnb@edge.cis.mcmaster.ca (John Benjamins) # disk_type = "CDC EMD 9720-1230" \ : ctlr = XD7053 \ : ncyl = 1633 : acyl = 2 : pcyl = 1635 : nhead = 15 : nsect = 82 \ : rpm = 3600 : bpt = 50400 : bps = 606 # # This is the list of disks that were supported by Sun, for the Emulex MD21 # controller. # # NB: Emulex no longer supports the MD21 controller in any way. Contact # GD California (510)417-7000 or Cerplex (714)258-5113 for MD21 support. # disk_type = "Micropolis 1355" \ : ctlr = MD21 \ : ncyl = 1018 : acyl = 2 : pcyl = 1024 : nhead = 8 : nsect = 34 \ : rpm = 3600 : bpt = 20832 disk_type = "Toshiba MK 156F" \ : ctlr = MD21 \ : ncyl = 815 : acyl = 2 : pcyl = 830 : nhead = 10 : nsect = 34 \ : rpm = 3600 : bpt = 20832 disk_type = "Micropolis 1558" \ : ctlr = MD21 \ : ncyl = 1218 : acyl = 2 : pcyl = 1224 : nhead = 15 : nsect = 35 \ : rpm = 3600 : bpt = 20833 # # Following is a list of sample embedded SCSI disk configurations. # disk_type = "Quantum ProDrive 80S" \ : ctlr = SCSI : fmt_time = 1 \ : cache = 0x07 : trks_zone = 6 : atrks = 0 : asect = 1 \ : ncyl = 832 : acyl = 2 : pcyl = 834 : nhead = 6 : nsect = 34 \ : rpm = 3662 : bpt = 16896 disk_type = "Seagate (CDC) Wren V 94181-702" \ : ctlr = SCSI : fmt_time = 4 \ : cache = 0x11 : trks_zone = 15 : asect = 2 \ : ncyl = 1543 : acyl = 2 : pcyl = 1545 : nhead = 15 : nsect = 48 \ : rpm = 3592 : bpt = 33408 disk_type = "Seagate (CDC) Wren VI 94191-766" \ : ctlr = SCSI : fmt_time = 4 \ : cache = 0x11 : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 1659 : acyl = 2 : pcyl = 1661 : nhead = 15 : nsect = 52 \ : rpm = 3600 : bpt = 31410 # From: sweh@spuddy.mew.co.uk (Stephen Harris) # I tried scsiinfo, which returned: # disk_type = "Seagate (CDC) Wren VII 94601-15" \ : ctlr = SCSI : fmt_time = 3 \ : atrks = 30 \ : ncyl = 1905 : acyl = 2 : pcyl = 1931 : nhead = 15 : nsect = 71 \ : rpm = 3597 : bpt = 41301 # Wren 8 - from Tim Kohler # disk_type = "Seagate (CDC) Wren VIII ST41650N" \ : ctlr = SCSI \ : cache = 0x11 : trks_zone = 15 : asect = 3 \ : ncyl = 2070 : acyl = 2 : pcyl = 2072 : nhead = 15 : nsect = 89 \ : rpm = 3597 : bpt = 45568 # Yes, this is a duplicate entry. If you're running SunOS 4.1.1 or earlier # on a sun4c (Sparcstation SLC/ELC/1/1+/IPC/IPX/2 without the patch for # large SCSI disks, problems arise for SCSI disks with a formatted capacity # greater than 2^21-1 bytes (1GB). Since the Wren VII is pretty close to # that anyways, here's an entry for it that stays within the limit. disk_type = "Seagate (CDC) Wren VII 94601-1.2G SunOS 4.1.1" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 1925 : acyl = 2 : pcyl = 1927 : nhead = 15 : nsect = 70 \ : rpm = 3597 : bpt = 41301 disk_type = "Maxtor XT-8380S" \ : ctlr = SCSI \ : cache = 0x11 : trks_zone = 8 : asect = 3 \ : ncyl = 1626 : acyl = 2 : pcyl = 1632 : nhead = 8 : nsect = 53 \ : rpm = 3600 : bpt = 31410 disk_type = "Maxtor XT-8760S" \ : ctlr = SCSI \ : cache = 0x11 : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 1614 : acyl = 2 : pcyl = 1632 : nhead = 15 : nsect = 54 \ : rpm = 3600 : bpt = 31410 # WARNING: this disk must be driven in hard sector mode and hard-configured # for 52 sectors/track. # disk_type = "Maxtor XT-8760E" \ : ctlr = SCSI \ : ncyl = 1616 : acyl = 6 : pcyl = 1632 : nhead = 15 : nsect = 50 \ : rpm = 3600 : bpt = 31410 partition = "Maxtor XT-8760E" \ : disk = "Maxtor XT-8760E" : ctlr = SCSI \ : a = 0, 97500 : b = 878, 63750 : c = 0, 1212000 : g = 130, 561000 \ : d = 130, 280500 : e = 504, 280500 : f = 963, 489750 : h = 0, 658500 # # This is the list of Sun supported disks for embedded SCSI. # disk_type = "CDC Wren IV 94171-344" \ : ctlr = SCSI : fmt_time = 4 \ : cache = 0x11 : trks_zone = 9 : asect = 3 \ : ncyl = 1545 : acyl = 2 : pcyl = 1549 : nhead = 9 : nsect = 46 \ : rpm = 3600 : bpt = 20833 # # Note: "SUN0999" entries constitute a "least common denominator" across # all drives of the appropriate size that Sun ships. Sun may # ship similarly sized drives from several different manufacturers, # maintaining plug-and-play replaceability by using a generic "SUN0999" # entry that works on all of them. It is sometimes possible to get a # little more space or slightly better performance by using the entry # for the disk manufacturer rather than the generic Sun entry. disk_type = "SUN0104" \ : ctlr = SCSI : fmt_time = 1 \ : trks_zone = 6 : atrks = 0 : asect = 1 \ : ncyl = 974 : acyl = 2 : pcyl = 1019 : nhead = 6 : nsect = 35 \ : rpm = 3662 : bpt = 16896 disk_type = "SUN0121" \ : ctlr = SCSI \ : ncyl = 1520 : acyl = 2 : pcyl = 1530 : nhead = 4 : nsect = 39 \ : rpm = 3575 : bpt = 19968 disk_type = "SUN0207" \ : ctlr = SCSI \ : trks_zone = 9 : atrks = 2: asect = 4 \ : ncyl = 1254 : acyl = 2 : pcyl = 1272 : nhead = 9 : nsect = 36 \ : rpm = 3600 : bpt = 18432 disk_type = "SUN0327" \ : ctlr = SCSI : fmt_time = 4 \ : cache = 0x11 : trks_zone = 9 : asect = 3 \ : ncyl = 1545 : acyl = 2 : pcyl = 1549 : nhead = 9 : nsect = 46 \ : rpm = 3600 : bpt = 20833 disk_type = "SUN0424" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 9 : asect = 2 \ : ncyl = 1151 : acyl = 2 : pcyl = 2500 : nhead = 9 : nsect = 80 \ : rpm = 4400 : bpt = 26000 disk_type = "SUN0535" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 1866 : acyl = 2 : pcyl = 2500 : nhead = 7 : nsect = 80 \ : rpm = 5400 : bpt = 31370 disk_type = "SUN0669" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 1614 : acyl = 2 : pcyl = 1632 : nhead = 15 : nsect = 54 \ : rpm = 3600 : bpt = 31410 disk_type = "Sun1.0G" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 1703 : acyl = 2 : pcyl = 1931 : nhead = 15 : nsect = 80 \ : rpm = 3597 : bpt = 41301 disk_type = "SUN2.1G" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 2733 : acyl = 2 : pcyl = 3500 : nhead = 19 : nsect = 80 \ : rpm = 5400 : bpt = 44823 # # Maxtor Xt-8610E notes: # # The drive is physically set to be hard-sectored at 53 sectors per track # as recommended by the emulex manual. However, the OS apparently wants # a sector per track for sparing, hence the number 52! # disk_type = "Maxtor XT-8610E" \ : ctlr = SCSI \ : ncyl = 1626 : acyl = 2 : pcyl = 1632 : nhead = 12 : nsect = 52 \ : rpm = 3600 : bpt = 31410 # Entry seems to work, but loses 10 Mbytes or so. # disk_type = "Seagate ST1239N SWIFT" \ : ctlr = SCSI \ : ncyl = 1264 : acyl = 2 : pcyl = 1266 : nhead = 9 \ : nsect = 35: rpm = 3600 : bpt=20232 : disk_type = "Maxtor LXT-200S" \ : ctlr = SCSI : fmt_time = 1 \ : trks_zone = 1 : atrks = 0 : asect = 1 \ : ncyl = 1117 : acyl = 2 : pcyl = 1119 : nhead = 7 : nsect = 43 \ : rpm = 3600 : bpt = 17000 # # From Karen Casella (kcasella@maxtor.com) at Maxtor Corp. # courtesy of Ken Lam (lam@jove.cofc.edu) # disk_type = "Maxtor LXT-340SY" \ : ctlr = SCSI \ : ncyl = 1355 : acyl = 2 : pcyl = 1546 : nhead = 7 : nsect = 70 \ : rpm = 3600 : bpt = 35840 # # From Larry D. Kelley (ldk@udev.cdc.com) # disk_type = "Maxtor LXT535ST" \ : cache = 0x00 \ : ctlr = SCSI : fmt_time = 4 : atrks = 7 \ : ncyl = 1547 : acyl = 5 : pcyl = 1552 : nhead = 11 \ : nsect = 61 : rpm = 3600 : bpt = 31370 partition = "Maxtor LXT535ST" \ : disk = "Maxtor LXT535ST" : ctlr = SCSI \ : c = 0, 1038037 # # From: Peter Ilieve peter@memex.co.uk # disk_type = "HP 97549T" \ : ctlr = SCSI : fmt_time = 4 \ : asect = 1 \ : ncyl = 1909 : acyl = 2 : pcyl = 1921 : nhead = 16 : nsect = 64 \ : rpm = 4002 : bpt = 38350 disk_type = "HP 97558" \ : ctlr = SCSI : fmt_time = 4 \ : asect = 0 : atrks = 26 \ : ncyl = 1933 : acyl = 2 : pcyl = 1962 : nhead = 15 : nsect = 72 \ : rpm = 4002 : bpt = 42840 disk_type = "HP 97556" \ : ctlr = SCSI : fmt_time = 4 \ : asect = 0 : atrks = 26 \ : ncyl = 1668 : acyl = 2 : pcyl = 1697 : nhead = 11 : nsect = 72 \ : rpm = 4002 : bpt = 42840 disk_type = "HP 97560" \ : ctlr = SCSI : fmt_time = 4 \ : asect = 0 : atrks = 26 \ : ncyl = 1933 : acyl = 2 : pcyl = 1962 : nhead = 19 : nsect = 72 \ : rpm = 4002 : bpt = 42840 # I didn't see the SUN1.3G from 4.1.2. I am using it on a factory # formatted Seagate ST41600N # disk_type = "SUN1.3G" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 17 : asect = 6 : atrks = 17 \ : ncyl = 1965 : acyl = 2 : pcyl = 3500 : nhead = 17 : nsect = 80 \ : rpm = 5400 : bpt = 44823 # # This is the list of supported disks for the Adaptec ACB4000 controller. # disk_type = "Micropolis 1304" \ : ctlr = ACB4000 \ : ncyl = 825 : acyl = 5 : pcyl = 830 : nhead = 6 : nsect = 17 \ : rpm = 3600 : bpt = 10416 : skew = 2 : precomp = 400 disk_type = "Micropolis 1325" \ : ctlr = ACB4000 \ : ncyl = 1022 : acyl = 2 : pcyl = 1024 : nhead = 8 : nsect = 17 \ : rpm = 3600 : bpt = 10416 : skew = 2 : precomp = 1024 disk_type = "Maxtor XT-1050" \ : ctlr = ACB4000 \ : ncyl = 1020 : acyl = 4 : pcyl = 1024 : nhead = 5 : nsect = 17 \ : rpm = 3600 : bpt = 10416 : skew = 2 : precomp = 1024 disk_type = "Fujitsu M2243AS" \ : ctlr = ACB4000 \ : ncyl = 752 : acyl = 2 : pcyl = 754 : nhead = 11 : nsect = 17 \ : rpm = 3600 : bpt = 10416 : skew = 2 : precomp = 754 disk_type = "Vertex V185" \ : ctlr = ACB4000 \ : ncyl = 1163 : acyl = 3 : pcyl = 1166 : nhead = 7 : nsect = 17 \ : rpm = 3600 : bpt = 10416 : skew = 2 : precomp = 1166 # We are using a number of 1004Mb drives (IBM 3.5 inch, quite *fast*) # distributed by Acropolis Systems, Inc. # These entries work for us on 4/60s and 4/75's and equivalent entries work on # HP9000/700s. Enjoy! disk_type = "ASI-1.0GIBM"\ :ctlr=SCSI:fmt_time=4\ :cache=0x11:trks_zone=15:asect=5:atrks=30\ :ncyl=1632:acyl=2:pcyl=1925:nhead=15:nsect=80\ :rpm=4316:bpt=41664 # From M.Lim@anu.edu.au # # Here is an entry for a Wren IX I posted to sun-managers recently # # It works on my SunOS 4.1.x systems. # disk_type = "Seagate ST42100N - Wren 9" \ : ctlr = SCSI : fmt_time = 4 \ : cache = 0x11 : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 2574 : acyl = 3 : pcyl = 2577 : nhead = 15 : nsect = 96 \ : rpm = 3600 : bpt = 57200 partition = "Seagate ST42100N - Wren 9" \ : disk = "Seagate ST42100N - Wren 9" : ctlr = SCSI \ : a = 0, 0 : b = 0, 0 : c = 0, 3706560 : d = 0, 0 \ : e = 0, 0 : f = 0, 0 : g = 0, 0 : h = 0, 0 # # From jdd@cdf.toronto.edu # disk_type = "Fujitsu M2263SA" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 1 : atrks = 10 \ : ncyl = 1652 : acyl = 2 : pcyl = 1658 : nhead = 15 : nsect = 53 \ : rpm = 3600 : bpt = 31296 # # From nir@ca44.zoran.hellnet.org # # I couldn't find a Fujitsu 2266SA 1.2GB entry in your format.faq. # I recently installed such a disk, and tried some entries sugested both from # my dealer, and from The Net. # # The best results I got was by using: disk_type = "Fujitsu M2266SA 1.2GB" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 1 : atrks = 10 \ : ncyl = 1652 : acyl = 2 : pcyl = 1658 : nhead = 15 : nsect = 85 \ : rpm = 3600 : bpt = 50830 # # From: John DiMarco (jdd@cdf.toronto.edu) # # Yes, this is a duplicate entry. If you're running SunOS 4.1.1 or earlier # on a sun4c (Sparcstation SLC/ELC/1/1+/IPC/IPX/2 without the patch for # large SCSI disks, problems arise for SCSI disks with a formatted capacity # greater than 2^21-1 bytes (1GB). Since the Fujitsu 2266 is pretty # close to that anyways, here's a format entry for the 2266 that stays # within the limit. Parameters courtesy of Ian Watt from Fujitsu Canada disk_type = "Fujitsu M2266SA 1GB" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 1642 : acyl = 2 : pcyl = 1658 : nhead = 15 : nsect = 85 \ : rpm = 3600 : bpt = 50910 # # From: poirot@mickey.jsc.nasa.gov (Daniel Poirot) # # I have just installed five Seagate ST3283N in different SPARC 1+ and 2 # machines. These drives are 'FAST SCSI' and format out to 240 Meg. The # following format.dat entry works fine for me! disk_type = "SeagateST3283N" \ : ctlr = SCSI \ : trks_zone = 5 : atrks = 0: asect = 0 \ : ncyl = 1689 : acyl = 2 : pcyl = 1691 : nhead = 5 : nsect = 57 \ : rpm = 4500 : bpt = 29184 # # From br@melb.bull.oz.au (Bret Robinson) # disk_type = "Maxtor XT-4380S" \ : ctlr = SCSI \ : ncyl = 1202 : acyl = 2 : pcyl = 1224 : nhead = 15 : nsect = 36 \ : rpm = 3600 : bpt = 18432 # # From : Philip Brown # # #Note that this is for the ESDI disk. #with an "ASDI" controller. although we fake it be be an SCSI. ignore #the final error about vendor-specific error. it really formats. # also, when you label it, it is 90% likely to lock up the # SCSI bus for a bit. try labeling immediately after. it should 99% #likely work. don't ask me why. but from then on, you should #have virtually no troubles with the drive. #note also that this has NOTHING to do #with the actual parameters of the drive. Which, I might add, are: # 10 heads, 6 disks, # 823 cylinders, variable sector size. disk_type = "Fujitsu M2246E"\ : ctlr = SCSI : fmt_time = 1 \ : trks_zone = 6 : atrks = 0 : asect = 1 \ : ncyl = 1196 : acyl = 2 : pcyl = 1198 : nhead = 6 : nsect = 35 \ : rpm = 3662 : bpt = 16896 partition = "Fujitsu M2246E" \ : disk = "Fujitsu M2246E" : ctlr = SCSI \ : a = 0 , 16170 : b = 77,28140 : c = 0, 251160 : g = 211,206850 # # From pete@guug.de (Pete Delaney) # I'm using the following format.dat entry, it SEEMS to be working ok: # disk_type = "Fujitsu-M2624S-512" \ : ctlr = SCSI : fmt_time = 1 \ : trks_zone = 15 : asect = 4 : atrks = 30 \ : ncyl = 1429 : acyl = 2 : pcyl = 1435 : nhead = 11 : nsect = 64 \ : rpm = 4400 : bpt = 39263 # # From kcasella@maxtor.com (Karen Casella) # # There are two models of Maxtor P0-12S, the newer one with 1795 cylinders, # the older with 1632 cylinders. # # Newer model Maxtor P0-12S disk_type = "Maxtor P0-12S (1795)" \ : ctlr = SCSI : fmt_time = 7 \ : ncyl = 1510 : acyl = 2 : pcyl = 1795 : nhead = 15 : nsect = 90 \ : rpm = 3600 : bpt = 46080 partition = "Maxtor P0-12S (1795)" \ : disk = "Maxtor P0-12S (1795)" : ctlr = SCSI \ : c = 0, 2038500 : g = 0, 2038500 # Older model Maxtor P0-12S disk_type = "Maxtor P0-12S (1632)" \ : ctlr = SCSI : fmt_time = 7 \ : ncyl = 1478 : acyl = 2 : pcyl = 1632 : nhead = 15 : nsect = 90 \ : rpm = 3600 : bpt = 46080 partition = "Maxtor P0-12S (1632)" \ : disk = "Maxtor P0-12S (1632)" : ctlr = SCSI \ : c = 0, 1995300 : g = 0, 1995300 # From: Sandra Smith (sandra@csri.toronto.edu) # Confirmed by Ian Watt at Fujitsu Canada disk_type = "Fujitsu M2652SA" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 1935 : acyl = 2 : pcyl = 1944 : nhead = 20 : nsect = 88 \ : rpm = 5400 : bpt = 52864 # From: John DiMarco (jdd@cdf.toronto.edu) # # Parameters from Ian Watt at Fujitsu Canada disk_type = "Fujitsu M2654SA" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 2174 : acyl = 2 : pcyl = 2179 : nhead = 21 : nsect = 88 \ : rpm = 5400 : bpt = 52864 # From: sun 4.1.2 format.dat version 1.24 disk_type = "CDC IPI 9720" \ : ctlr = ISP-80 \ : ncyl = 1631 : acyl = 1 : pcyl = 1633 : nhead = 15 : nsect = 82 \ : rpm = 3600 : bpt = 50400 : skew = 0 : precomp = 0 partition = "CDC IPI 9720" \ : disk = "CDC IPI 9720" : ctlr = ISP-80 \ : a = 0, 33210 : b = 27, 131610 : c = 0, 2006130 : g = 134, 196800 \ : h = 294, 1644510 disk_type = "CDC IPI 9722" \ : ctlr = ISP-80 \ : ncyl = 1630 : acyl = 1 : pcyl = 1632 : nhead = 7 : nsect = 156 \ : rpm = 3600 : bpt = 100800 : skew = 0 : precomp = 0 partition = "CDC IPI 9722" \ : disk = "CDC IPI 9722" : ctlr = ISP-80 \ : a = 0, 33852 : b = 31, 132132 : c = 0, 1779960 : g = 152, 197652 \ : h = 333, 1416324 disk_type = "Seagate IPI ZBR Elite" \ : ctlr = "ISP-80" \ : ncyl = 1893 : acyl = 1 : pcyl = 1895 : nhead = 17 : nsect = 78 \ : rpm = 5400 : bpt = 50400 : skew = 0 : precomp = 0 partition = "Seagate IPI ZBR Elite" \ : disk = "Seagate IPI ZBR Elite" : ctlr = ISP-80 \ : a = 0, 34476 : b = 26, 132600 : c = 0, 2510118 : g = 126, 663000 \ : h = 626, 1680042 disk_type = "ST83220K" \ : ctlr = "ISP-80" \ : ncyl = 2652 : acyl = 1 : pcyl = 2653 : nhead = 19 : nsect = 102 \ : rpm = 4365 : bpt = 63840 : skew = 0 : precomp = 0 # From: Charles A. Uretsky (wbbart!cau@abars.att.com) # thanks to the following: # # Michiel Steltman # Brian Bartholomew # disk_type = "Seagate ST1480N" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 9 : asect = 4 \ : ncyl = 1456 : acyl = 2 : pcyl = 1476 : nhead = 9 : nsect = 64 \ : rpm = 4400 : bpt = 37037 # From: Bevin Steer (ccbjs@levels.unisa.edu.au) # # The following is what I am experimenting with. Please don't hesitate to # contact me if you see something wrong or silly...or know what the real # numbers should be :-) # disk_type = "DEC_RZ58" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 8 : atrks = 0 \ : ncyl = 2112 : acyl = 3 : pcyl = 2115 : nhead = 15 : nsect = 85 \ : rpm = 5400 : bpt = 44000 # Stab in the dark, what should it be? # partition = "DEC_RZ58_whole_disk" \ : disk = "DEC_RZ58" : ctlr = SCSI \ : c=0,2692800 # From jdd@cdf.toronto.edu (John DiMarco) # # Courtesy of Open Storage Solutions, bpt added from Seagate specs (avg of # bpt for inner and outer tracks). disk_type = "SUN2.1G" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 2733 : acyl = 2 : pcyl = 3500 : nhead = 19 : nsect = 80 \ : rpm = 5400 : bpt = 44823 # # From jdd@cdf.toronto.edu (John DiMarco) # # Params courtesy of Open Storage Solutions except for # bpt, which I set to be the midpoint between the bpt figure for the # inner and outer tracks. # disk_type = "Seagate ST42400N Elite 2" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 2604 : acyl = 2 : pcyl = 2624 : nhead = 19 \ : nsect = 84 : rpm = 5400 : bpt = 48720 partition = "Seagate ST42400N Elite 2" \ : disk = "Seagate ST42400N Elite 2" : ctlr = SCSI \ : c = 0, 4155984 # # From: philf@hst.att.com (Phil Fischer) # disk_type = "Seagate Elite ST43400N-3.5G" \ : ctlr = SCSI : fmt_time = 8 \ : cache = 0x11 : trks_zone = 20 : asect = 6 : atrks = 20 \ : ncyl = 2736 : acyl = 2 : pcyl = 2738 : nhead = 21 : nsect = 99 \ : rpm = 5400 : bpt = 49000 partition = "Seagate Elite ST43400N-3.5G" \ : disk = "Seagate Elite ST43400N-3.5G" : ctlr = SCSI \ : a = 0, 2843360 : b = 1367, 2843360 # # From kcasella@maxtor.com (Karen Casella) # disk_type = "Maxtor P1-17S" \ : ctlr = SCSI : fmt_time = 9 \ : trks_zone = 19 \ : ncyl = 1816 : acyl = 2 : pcyl = 1818 : nhead = 19 : nsect = 83 \ : rpm = 3600 : bpt = 42496 partition = "Maxtor P1-17S" \ : disk = "Maxtor P1-17S" : ctlr = SCSI \ : a = 0, 78850 : b = 50, 78850 : c = 0, 2863832 : d = 100, 78850 \ : g = 150, 2469582 : h = 1716, 78850 disk_type = "Maxtor P1-17S NB" \ : ctlr = SCSI \ : ncyl = 1711 : acyl = 2 : pcyl = 1778 : nhead = 19 : nsect = 90 \ : rpm = 3600 : bpt = 46080 partition = "Maxtor P1-17S NB" \ : disk = "Maxtor P1-17S NB" : ctlr = SCSI \ : c = 0, 2925810 : g = 0, 2925810 # # From: kimc@w8hd.org (Kim Culhan) # This is a 'revised' format.dat which was supplied by Maxtor tech support # for the MXT1240S. # disk_type = "Maxtor MXT1240S" \ : ctlr = SCSI : fmt_time = 7 \ : ncyl = 2306 : acyl = 2 : pcyl = 2368 : nhead = 15 : nsect = 70 \ : rpm = 6300 : bpt = 31410 partition = "Maxtor MXT1240S" \ : disk = "Maxtor MXT1240S" : ctlr = SCSI \ : c = 0, 2421300 : g = 0, 2421300 # # from Michael Chang (nulspace@cs.umd.edu) # disk_type = "CONNER 30170E" \ : ctlr = SCSI \ : ncyl = 897 : acyl = 2 : pcyl = 903 : nhead = 8 : nsect = 46 \ : rpm = 3822 : bpt = 23552 partition = "CONNER 30170E" \ : disk = "CONNER 30170E" : ctlr = SCSI \ : a = 0, 14720 : b = 40, 40480 : c = 0, 330096 : g = 150, 274896 # # from sgolson@trilobyte.com (Steve Golson) # # This drive is sold by DEC as the DEC DSP3105 # disk_type = "Maxtor DXP3105S" \ : ctlr = SCSI : fmt_time = 1 \ : ncyl = 2568 : acyl = 2 : pcyl = 2570 : nhead = 14 : nsect = 57 \ : rpm = 5400 : bpt = 29640 # # From (Dan Butzer) butzer@cranel.com: # disk_type = "HP C3010 / Cranel 2.0GB Fast SCSI2 H10" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 28515 : asect = 0 : atrks = 1311 \ : ncyl = 2165 : acyl = 2 : pcyl = 2325 : nhead = 19 : nsect = 95 \ : rpm = 5400 : bpt = 44032 # # From Rex Mayne # disk_type = "HP97548SU 664MB" \ :ctlr = SCSI \ :trks_zone = 1 : asect = 1 : atrks = 112 \ :ncyl = 1445 : acyl = 2 : pcyl = 1457 : nhead = 16 \ :nsect = 56 : rpm = 4002 : bpt = 37449 partition = "HP97548SU 664MB" \ :disk = "HP97548SU 664MB" : ctlr = SCSI \ :a = 0,35840 : b = 40,71680 : c = 0,1294720 \ :g = 240,197120 : h = 680,342720 # # From louis@marco.de (Ju"rgen Fluk) # disk_type = "Conner CP3540" \ : ctlr = SCSI \ : ncyl = 1805 : acyl = 2 : pcyl = 1807 : nhead = 12 \ : nsect = 49 : rpm = 4400 : bpt = 35840 # # From: kcasella@maxtor.com (Karen Casella) # disk_type = "Maxtor 7213SR NB" \ : ctlr = SCSI \ : ncyl = 1595 : acyl = 3 : pcyl = 1698 : nhead = 4 : nsect = 65 \ : rpm = 3600 : bpt = 33280 partition = "Maxtor 7213SR NB" \ : disk = "Maxtor 7213SR NB" : ctlr = SCSI \ : c = 0, 414700 : g = 0, 414700 # # From sam@ics.uci.edu (Sam Horrocks) # disk_type = "Seagate ST11200N" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 12 : atrks = 30 \ : ncyl = 1714 : acyl = 1 : pcyl = 1715 : nhead = 15 : nsect = 80 \ : rpm = 5411 : bpt = 40960 partition = "Seagate ST11200N" \ : disk = "Seagate ST11200N" : ctlr = SCSI \ : a = 0, 2056800 : b = 0, 0 : c = 0, 2056800 : g = 0, 0 # # From jdd@cdf.toronto.edu (John DiMarco) # disk_type = "CONNER 30200" \ : ctlr = SCSI : fmt_time = 1 \ : ncyl = 2121 : acyl = 2 : asect = 1 : pcyl = 2123 \ : nhead = 4 : nsect = 49 \ : rpm = 3600 : bpt = 25088 partition = "CONNER 30200" \ : disk = "CONNER 30200" : ctlr = SCSI \ : c = 0, 415716 # From: Thomas Tornblom # This is the format.dat entry I used for using a 44M SyQuest drive on a # SparcStation SLC. The SCSI-driver, for 4.1.1 and 4.1.2 at least, needs # one binary patch and synchronous SCSI needs to be turned off in the # kernel. # # What is needed is two kernel patches, a format.dat for the drive and a # disk formatted with 512 byte blocks (I formatted one in a Macintosh). # # The kernel patches are small and can be done without source. # # # adb -k -w /vmunix /dev/mem # physmem fec # scsi_options?X # _scsi_options: # _scsi_options: 78 # ?W 38 # _scsi_options: 0x78 = 0x38 <- Turn off Synch SCSI # sd_findslave+0x1b0?i # _sd_findslave+0x1b0: mov -0x1, %l5 # # _sd_findslave+0x1b4: st %l5, [%fp - 0x8] <- Change this # ?W c027bff8 # _sd_findslave+0x1b4: 0xea27bff8 = 0xc027bff8 # sd_findslave+0x1b0?i # _sd_findslave+0x1b0: mov -0x1, %l5 # # _sd_findslave+0x1b4: st %g0, [%fp - 0x8] <- to this # # _sd_findslave+0x1b8: st %g0, [%fp - 0x4] # # 'what /sys/sun4c/OBJ/sd.o' said version 1.98 90/08/30 on my system, if # yours is different, you might have to check around to find the # offending sequence of instructions. # disk_type = "SyQuest SQ555" \ : ctlr = SCSI : fmt_time = 3 \ : ncyl = 1273 : acyl = 2 : pcyl = 1275 : nhead = 2 : nsect = 34 \ : rpm = 3220 : bpt = 16896 partition = "SyQuest SQ555" \ : disk = "SyQuest SQ555" : ctlr = SCSI \ : c = 0, 86564 # From Fabrice Cuq (fabrice@cisk.atmos.ucla.edu) # DEC DSP3160S -- Formatted Capacity: 1526MB disk_type = "Arte DEC DSP3160S" \ : ctlr = SCSI : fmt_time = 13 \ : ncyl = 1744 : acyl = 2 : pcyl = 1746 : nhead = 16 : nsect = 112 \ : rpm = 5403 : bpt = 57344 # From: Richard.Hellier # # Here is a format.dat entry for the IBM 0663 E15 1.2G disk, # as supplied by the vendor. disk_type = "IBM 0663-E15" : ctlr = SCSI \ : ncyl = 3182 : acyl = 2 : pcyl = 3184 \ : nhead = 20 : nsect = 37 : rpm = 4316 : bpt = 31410 # From: greg@serveme.chi.il.us (Gregory Gulik) # # I got this information from Fujitsu technical support. # disk_type = "Fujitsu-M2694ESA" \ : ctlr = SCSI \ : cache = 0x11 : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 1830 : acyl = 2 : pcyl = 1832 : nhead = 15 : nsect = 77 \ : rpm = 5400 : bpt = 31410 # From: Peter W. Osel # # Received these directly from Quantum Corp., USA # disk_type = "Quantum LPS 105S" \ : ctlr = SCSI \ : ncyl = 1221 : acyl = 2 : pcyl = 1223 : nhead = 4 : nsect = 42 \ : rpm = 3600 : bpt = 21504 disk_type = "Quantum LPS 120S" \ : ctlr = SCSI \ : ncyl = 1987 : acyl = 2 : pcyl = 1989 : nhead = 2 : nsect = 60 \ : rpm = 3660 : bpt = 30720 disk_type = "Quantum LPS 240S" \ : ctlr = SCSI \ : ncyl = 1995 : acyl = 2 : pcyl = 1997 : nhead = 4 : nsect = 60 \ : rpm = 3660 : bpt = 30720 disk_type = "Quantum PD 120S" \ : ctlr = SCSI \ : ncyl = 1114 : acyl = 2 : pcyl = 1116 : nhead = 5 : nsect = 42 \ : rpm = 3600 : bpt = 21504 disk_type = "Quantum PD 170S" \ : ctlr = SCSI \ : ncyl = 1117 : acyl = 2 : pcyl = 1119 : nhead = 7 : nsect = 42 \ : rpm = 3600 : bpt = 21504 disk_type = "Quantum PD 210S" \ : ctlr = SCSI \ : ncyl = 1189 : acyl = 2 : pcyl = 1191 : nhead = 7 : nsect = 49 \ : rpm = 3600 : bpt = 25088 disk_type = "Quantum PD 425S" \ : ctlr = SCSI \ : ncyl = 1540 : acyl = 2 : pcyl = 1542 : nhead = 9 : nsect = 60 \ : rpm = 3600 : bpt = 30720 disk_type = "Quantum ELS 85S" \ : ctlr = SCSI \ : ncyl = 1535 : acyl = 2 : pcyl = 1537 : nhead = 2 : nsect = 54 \ : rpm = 3600 : bpt = 27648 disk_type = "Quantum ELS 127S" \ : ctlr = SCSI \ : ncyl = 1541 : acyl = 2 : pcyl = 1543 : nhead = 3 : nsect = 54 \ : rpm = 3600 : bpt = 27648 disk_type = "Quantum ELS 170S" \ : ctlr = SCSI \ : ncyl = 1542 : acyl = 2 : pcyl = 1544 : nhead = 4 : nsect = 54 \ : rpm = 3600 : bpt = 27648 disk_type = "Quantum GoDrive 120S" \ : ctlr = SCSI \ : ncyl = 1067 : acyl = 2 : pcyl = 1069 : nhead = 4 : nsect = 56 \ : rpm = 3600 : bpt = 28672 disk_type = "Quantum GoDrive 160S" \ : ctlr = SCSI \ : ncyl = 1413 : acyl = 2 : pcyl = 1415 : nhead = 4 : nsect = 58 \ : rpm = 3600 : bpt = 29696 disk_type = "Quantum LPS 525S" \ : ctlr = SCSI \ : ncyl = 2444 : acyl = 2 : pcyl = 2446 : nhead = 6 : nsect = 70 \ : rpm = 4500 : bpt = 35840 disk_type = "Quantum PD 700S" \ : ctlr = SCSI \ : ncyl = 2441 : acyl = 2 : pcyl = 2443 : nhead = 8 : nsect = 70 \ : rpm = 4500 : bpt = 35840 disk_type = "Quantum PD 1050S" \ : ctlr = SCSI \ : ncyl = 2444 : acyl = 2 : pcyl = 2446 : nhead = 12 : nsect = 70 \ : rpm = 4500 : bpt = 35840 disk_type = "Quantum PD 1225S" \ : ctlr = SCSI \ : ncyl = 2442 : acyl = 2 : pcyl = 2444 : nhead = 14 : nsect = 70 \ : rpm = 4500 : bpt = 35840 # From: cc_koper@rcvie.co.at (Koper Zangocyan) # DEC RZ55 disk format.dat entry is the same as "Micropolis 1558" # This works fine on a Sun-4/40 with SunOS 4.1.2 disk_type = "RZ55" \ : ctlr = SCSI \ : ncyl = 1218 : acyl = 2 : pcyl = 1224 : nhead = 15 : nsect = 35 \ : rpm = 3600 : bpt = 20833 partition = "RZ55" \ : disk = "RZ55" : ctlr = SCSI \ : a = 0, 32025 : b = 61, 59850 : c = 0, 639450 : g = 175, 547575 # From: cc_koper@rcvie.co.at (Koper Zangocyan) # DEC RZ24 disk format.dat entry. # This works fine on a Sun-4/40 with SunOS 4.1.2 disk_type = "RZ24" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 8 \ : ncyl = 1344 : acyl = 2 : pcyl = 1348 \ : nhead = 8 : nsect = 38 : rpm = 3497 : bpt = 19456 partition = "RZ24" \ : disk = "RZ24" : ctlr = SCSI \ : a = 0, 0 : b = 0, 0 : c = 0, 409792 # # From: olav.lerbrekk@geology.uio.no (Olav Lerbrekk) # disk_type = "Seagate ST12550N" \ : ctlr = SCSI : fmt_time = 4 \ : cache = 0x0 : trks_zone = 19 : asect = 9 : atrks = 19 \ : ncyl = 2747 : acyl = 2 : pcyl = 2708 : nhead = 19 : nsect = 80 \ : rpm = 7200 : bpt = 40960 # # From: morrow@cns.ucalgary.ca (Bill Morrow) # # Format entry for M2511A magneto-optical 128MB removeable media drive. disk_type = "Fujitsu M2511A" \ : ctlr = SCSI : fmt_time = 12 \ : ncyl = 9950 : acyl = 2 : pcyl = 9952 : nhead = 1 : nsect = 25 \ : rpm = 3600 : bpt = 12800 # # From: gcs@tstsp0.dsto.gov.au (Gary Speechley) # # These are entries for the Maxtor Tahiti IIm drive. Credit where credit # is due, however: most of the data is supplied through the device driver # files from Advanced Archival Products of Greenwood Village Colorado. # My modifications are for the single partition "DATA" drives. # # This is for the Maxoptix Tahiti IIm drive - SYSTEM # disk_type = "MAXOPTIX (NON-ISO, 512b) SYSTEM" \ : ctlr = SCSI \ : ncyl = 15081 : acyl = 2 : pcyl = 15083 : nhead = 1 : nsect = 60 \ : rpm = 2200 : bpt = 36600 : bps = 610 : disk_type = "MAXOPTIX (NON-ISO, 1024b) SYSTEM" \ : ctlr = SCSI \ : ncyl = 15104 : acyl = 2 : pcyl = 15106 : nhead = 1 : nsect = 66 \ : rpm = 2200 : bpt = 74052 : bps = 1122 : # # This is for the Maxoptix Tahiti IIm drive - DATA (GCS 06-Apr-93) # disk_type = "MAXOPTIX (NON-ISO, 512b) DATA" \ : ctlr = SCSI \ : ncyl = 15081 : acyl = 2 : pcyl = 15083 : nhead = 1 : nsect = 60 \ : rpm = 2200 : bpt = 36600 : bps = 610 : disk_type = "MAXOPTIX (NON-ISO, 1024b) DATA" \ : ctlr = SCSI \ : ncyl = 15104 : acyl = 2 : pcyl = 15106 : nhead = 1 : nsect = 66 \ : rpm = 2200 : bpt = 74052 : bps = 1122 : # From: Todd Gamble # # I got the drive and format.dat entry from DATALINK (800-448-6314). disk_type = "HP C2247 1.05GB" \ : ctlr = SCSI \ : trks_zone = 6925 : asect = 0 : atrks = 897\ : ncyl = 1661 : acyl = 2 : pcyl = 2018: nhead = 13\ : nsect = 95 : rpm = 5400 : bpt = 49152 partition = "HP C2247 1.05GB" \ : disk="HP C2247 1.05GB" : ctlr = SCSI \ : c = 0, 2051335 : g = 0, 1640080: h = 1328, 411255 # From: Chris Dean # # DEC DSP3210 2103MB # disk_type = "DEC DSP3210 2 GB" \ : ctlr = SCSI : fmt_time = 13 \ : ncyl = 3040 : acyl = 2 : pcyl = 3042 : nhead = 16 : nsect = 86 \ : rpm = 5400 : bpt = 44032 partition = "DEC DSP3210 2 GB" \ : disk = "DEC DSP3210 2 GB" : ctlr = SCSI \ : c = 0, 4183040 # From: Christopher Lott # # IBM 0662 S12 drive - approximately 1.05Gb # most parameters retrieved from drive using format; # rpm, bpt entered from the specification sheet. # disk_type = "IBM 0662-S12" \ : ctlr = SCSI : fmt_time = 4 : ncyl = 3002 : acyl = 2 \ : pcyl = 3004 : nhead = 6 : nsect = 114 \ : rpm = 5400 : bpt = 31410 # From: Dean Cookson # As received from DEC: # disk_type = "DEC DSP5350" \ : ctlr = SCSI : fmt_time=9 \ : cache = 11 : trks_zone = 25 : asect = 25 : atrks = 0 \ : ncyl = 3053 : acyl = 2 : pcyl = 3055 : nhead = 25 : nsect = 91 \ : rpm = 5400 : bpt = 46592 # From: reilly@horta.shr.dec.com (Stephen Reilly) # # I am DEC's Engineer supervisor for the support # of DEC devices on Sun SPARC systems. I would like to request that these # [3] attached format.dat entries be added public domain version. # # 1.05 GB 3 1/2" form factor disk ( DEC P/N: SWSD3-SA) disk_type = "DEC_RZ26" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 2568 : acyl = 2 : pcyl = 2570 : nhead = 14 : nsect = 57 \ : rpm = 5400 : bpt = 29184 partition = "DEC_RZ26" \ : disk = "DEC_RZ26" :ctlr = SCSI \ : a = 0, 66234 : b = 83, 132468 : c = 0, 2049264 : g = 249, 1850562 # # 2.1 GB 3 1/2" form factor disk (DEC P/N: SWSD3-SB) # Note: This is a banded drive so the number of sectors is an average over # the bands. disk_type = "DEC_RZ28" \ : ctlr = SCSI : fmt_time = 5 \ : ncyl = 3043 : acyl = 2 : pcyl = 3045 : nhead = 16 : nsect = 84 \ : rpm = 5400 : bpt = 43008 partition = "DEC_RZ28" \ : disk = "DEC_RZ28" :ctlr = SCSI \ : a = 0, 64512 : b = 48, 196224 : c = 0, 4089792 : g = 194, 3827712 # # 3.57 GB 5.25 form factor disk (DEC P/N: SWSD5-SA) # Note: This is a banded drive so the number of sectors is an average over # the bands. disk_type = "DEC_RZ74" \ : ctlr = SCSI : fmt_time = 9 \ : ncyl = 3053 : acyl = 2 : pcyl = 3055 : nhead = 25 : nsect = 91 \ : rpm = 5400 : bpt = 46592 partition = "DEC_RZ74" \ : disk = "DEC_RZ74" : ctlr = SCSI \ : a = 0, 65975 : b = 29, 193375 : c = 0, 4192825 \ : g = 114, 3931200 : h = 1843, 2752750 # # From: adcock@gsc.emr.ca # disk_type = "Seagate ST11900N" \ : ctlr = SCSI \ : ncyl = 2619 : acyl = 2 : pcyl = 2621 : nhead = 15 : nsect = 83 \ : rpm = 5411 : bpt = 48140 partition = "Seagate ST11900N" \ : disk = "Seagate ST11900N" : ctlr = SCSI \ : b = 0, 498000 : c = 0, 3260655 : h = 400, 2761410 # # From: dick@netcom.com (Richard Arnold) # disk_type = "Seagate ST12400N 2.4GB" \ : ctlr = SCSI : fmt_time = 4 \ : cache = 0x0 : trks_zone = 19 : asect = 1 : atrks = 0 \ : ncyl = 2668 : acyl = 2 : pcyl = 2621 : nhead = 19 : nsect = 82 \ : rpm = 5411 : bpt = 41984 partition = "Seagate ST12400N 2.4GB" \ : disk = "Seagate ST12400N 2.4GB" : ctlr = SCSI \ : a = 0, 32718 : b =21, 65436 : c = 0, 4156744 : g = 63, 4058590 # # From: Richard Ravich # Here's the latest version of format.dat that Micropolis has prepared. # disk_type = "Micropolis 1674-7" \ : ctlr = SCSI \ : ncyl = 1255: acyl = 3: pcyl = 1249: nhead = 7: nsect = 35 \ : rpm = 3600: bpt = 20832: trks_zone = 7: fmt_time = 4 \ : atrks = 21: asect = 4 disk_type = "Micropolis 1684-7" \ : ctlr = SCSI \ : ncyl = 1785: acyl = 3: pcyl = 1780: nhead = 7: nsect = 53 \ : rpm = 3600: bpt = 31248: trks_zone = 7: fmt_time = 4 \ : atrks = 21: asect = 4 disk_type = "Micropolis 1624-7" \ : ctlr = SCSI \ : ncyl = 1647: acyl = 3: pcyl = 2112: nhead = 7: nsect = 114 \ : rpm = 3600: bpt = 67900: trks_zone = 7: fmt_time = 4 \ : atrks = 21: asect = 4 disk_type = "Micropolis 1578-15" \ : ctlr = SCSI \ : ncyl = 1231: acyl = 3: pcyl = 1224: nhead = 15: nsect = 35 \ : rpm = 3600: bpt = 20832: trks_zone = 15: fmt_time = 4 \ : atrks = 45: asect = 8 disk_type = "Micropolis 1588-15" \ : ctlr = SCSI \ : ncyl = 1637: acyl = 3: pcyl = 1632: nhead = 15: nsect = 53 \ : rpm = 3600: bpt = 31410: trks_zone = 15: fmt_time = 4 \ : atrks = 45: asect = 8 disk_type = "Micropolis 1598-15" \ : ctlr = SCSI \ : ncyl = 1931: acyl = 3: pcyl = 1928: nhead = 15: nsect = 70 \ : rpm = 3600: bpt = 41664: trks_zone = 15: fmt_time = 4 \ : atrks = 45: asect = 8 disk_type = "Micropolis 1528-15" \ : ctlr = SCSI \ : ncyl = 2102: acyl = 3: pcyl = 2100: nhead = 15: nsect = 83 \ : rpm = 3600: bpt = 42496: trks_zone = 15: fmt_time = 5 \ : atrks = 45: asect = 8 disk_type = "Micropolis 1548-15" \ : ctlr = SCSI \ : ncyl = 1701: acyl = 3: pcyl = 2112: nhead = 15: nsect = 131 \ : rpm = 3600: bpt = 79218: trks_zone = 15: fmt_time = 6 \ : atrks = 45: asect = 8 disk_type = "Micropolis 2105-8" \ : ctlr = SCSI \ : ncyl = 1448: acyl = 3: pcyl = 1760: nhead = 8: nsect = 94 \ : rpm = 5400: bpt = 51000: trks_zone = 8: fmt_time = 4 \ : atrks = 25: asect = 5 disk_type = "Micropolis 2112-15" \ : ctlr = SCSI \ : ncyl = 1452: acyl = 3: pcyl = 1760: nhead = 15: nsect = 94 \ : rpm = 5400: bpt = 55556: trks_zone = 15: fmt_time = 5 \ : atrks = 45: asect = 6 disk_type = "Micropolis 1908-15" \ : ctlr = SCSI \ : ncyl = 1890: acyl = 3: pcyl = 2112: nhead = 15: nsect = 95 \ : rpm = 5400: bpt = 56241: trks_zone = 15: fmt_time = 5 \ : atrks = 45: asect = 8 disk_type = "Micropolis 1924-21" \ : ctlr = SCSI \ : ncyl = 2072: acyl = 3: pcyl = 2280: nhead = 21: nsect = 94 \ : rpm = 5400: bpt = 42496: trks_zone = 21: fmt_time = 5 \ : atrks = 63: asect = 11 disk_type = "Micropolis 1936-21" \ : ctlr = SCSI \ : ncyl = 2772: acyl = 3: pcyl = 2780: nhead = 21: nsect = 101 \ : rpm = 5400: bpt = 51718: trks_zone = 21: fmt_time = 6 \ : atrks = 63: asect = 11 disk_type = "Micropolis 2210-09" \ : ctlr = SCSI \ : ncyl = 2099: acyl = 3: pcyl = 2372: nhead = 9: nsect = 109 \ : rpm = 5400: bpt = 57770: trks_zone = 9: fmt_time = 4 \ : atrks = 27: asect = 6 disk_type = "Micropolis 2108-10" \ : ctlr = SCSI \ : ncyl = 1450: acyl = 3: pcyl = 1760: nhead = 10: nsect = 94 \ : rpm = 5400: bpt = 51000: trks_zone = 10: fmt_time = 4 \ : atrks = 30: asect = 5 disk_type = "Micropolis 2205-05" \ : ctlr = SCSI \ : ncyl = 2088: acyl = 3: pcyl = 2372: nhead = 5: nsect = 109 \ : rpm = 5400: bpt = 57770: trks_zone = 5: fmt_time = 3 \ : atrks = 15: asect = 6 disk_type = "Micropolis 1926-15" \ : ctlr = SCSI \ : ncyl = 2769: acyl = 3: pcyl = 2772: nhead = 15: nsect = 101 \ : rpm = 5400: bpt = 51718: trks_zone = 15: fmt_time = 5 \ : atrks = 45: asect = 8 disk_type = "Micropolis 2217-15" \ : ctlr = SCSI \ : ncyl = 2105: acyl = 3: pcyl = 2372: nhead = 15: nsect = 109 \ : rpm = 5400: bpt = 57770: trks_zone = 15: fmt_time = 5 \ : atrks = 45: asect = 6 partition = "Micropolis 2217-15" \ : disk = "Micropolis 2217-15" : ctlr = SCSI \ : a = 0, 32700: b = 20, 65400: c = 0, 3441675: g = 60, 3343575 partition = "Micropolis 2210-09" \ : disk = "Micropolis 2210-09" : ctlr = SCSI \ : a = 0, 33354: b = 34, 66708: c = 0, 2059119: g = 102, 1959057 partition = "Micropolis 2205-05" \ : disk = "Micropolis 2205-05" : ctlr = SCSI \ : a = 0, 32700: b = 60, 65400: c = 0, 1137960: g = 180, 1039860 partition = "Micropolis 2108-10" \ : disk = "Micropolis 2108-10" : ctlr = SCSI \ : a = 0, 31960: b = 34, 63920: c = 0, 1363000: g = 102, 1267120 partition = "Micropolis 1926-15" \ : disk = "Micropolis 1926-15" : ctlr = SCSI \ : a = 0, 33330: b = 22, 66660: c = 0, 4195035: g = 66, 4095045 partition = "Micropolis 1674-7" \ : disk = "Micropolis 1674-7" : ctlr = SCSI \ : a = 0, 16415: b = 67, 32830: c = 0, 307475: g = 201, 258230 partition = "Micropolis 1684-7" \ : disk = "Micropolis 1684-7" : ctlr = SCSI \ : a = 0, 32648: b = 88, 65296: c = 0, 662235: g = 264, 564291 partition = "Micropolis 1624-7" \ : disk = "Micropolis 1624-7" : ctlr = SCSI \ : a = 0, 32718: b = 41, 65436: c = 0, 1314306: g = 123, 1216152 partition = "Micropolis 1578-15" \ : disk = "Micropolis 1578-15" : ctlr = SCSI \ : a = 0, 32550: b = 62, 65100: c = 0, 646275: g = 186, 548625 partition = "Micropolis 1588-15" \ : disk = "Micropolis 1588-15" : ctlr = SCSI \ : a = 0, 32595: b = 41, 65190: c = 0, 1301415: g = 123, 1203630 partition = "Micropolis 1598-15" \ : disk = "Micropolis 1598-15" : ctlr = SCSI \ : a = 0, 32550: b = 31, 65100: c = 0, 2027550: g = 93, 1929900 partition = "Micropolis 1528-15" \ : disk = "Micropolis 1528-15" : ctlr = SCSI \ : a = 0, 32370: b = 26, 64740: c = 0, 2616990: g = 78, 2519880 partition = "Micropolis 1548-15" \ : disk = "Micropolis 1548-15" : ctlr = SCSI \ : a = 0, 33405: b = 17, 66810: c = 0, 3342465: g = 51, 3242250 partition = "Micropolis 2105-8" \ : disk = "Micropolis 2105-8" : ctlr = SCSI \ : a = 0, 32336: b = 43, 64672: c = 0, 1088896: g = 129, 991888 partition = "Micropolis 2112-15" \ : disk = "Micropolis 2112-15" : ctlr = SCSI \ : a = 0, 33840: b = 24, 67680: c = 0, 2047320: g = 72, 1945800 partition = "Micropolis 1908-15" \ : disk = "Micropolis 1908-15" : ctlr = SCSI \ : a = 0, 32775: b = 23, 65550: c = 0, 2693250: g = 69, 2594925 partition = "Micropolis 1924-21" \ : disk = "Micropolis 1924-21" : ctlr = SCSI \ : a = 0, 33558: b = 17, 67116: c = 0, 4090128: g = 51, 3989454 partition = "Micropolis 1936-21" \ : disk = "Micropolis 1936-21" : ctlr = SCSI \ : a = 0, 33936: b = 16, 67872: c = 0, 5879412 \ : g = 48, 2846382 : h = 1390, 2931222 # This is a entry for IBM 0663L12 (1004 Mb). # It was created using scsinfo 3.1. # It seems to work fine with my ELC (4/25) and Sun OS 4.1.3. # jonas@interactive.se disk_type = "IBM 0663L12" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 15 : atrks = 0 : asect = 0 \ : ncyl = 1979 : acyl = 2 : pcyl = 2051 : nhead = 15 : nsect = 66 \ : rpm = 4316 : bpt = 38808 partition = "IBM 0663L12" \ : disk = "IBM 0663L12" : ctlr = SCSI \ : c = 0, 1959210 # From: Gerard Hynes # Please find included the format.dat and partition data for the new # Micropolis 2217-15 3.5" Fast SCSI-2 disk drive. This is a 1.765GB # formatted unit. # # This data provided by Micropolis technical support. disk_type = "Micropolis 2217-15" \ : ctlr = SCSI \ : ncyl = 2105: acyl = 3: pcyl = 2372: nhead = 15: nsect = 109 \ : rpm = 5400: bpt = 57770: trks_zone = 15: fmt_time = 5 \ : atrks = 45: asect = 6 partition = "Micropolis 2217-15" \ : disk = "Micropolis 2217-15" : ctlr = SCSI \ : a = 0, 32700: b = 20, 65400: c = 0, 3441675: g = 60, 3343575 # From: mingso@netcom.com (Ming Yau So) # # The entry was provided by Stephen Reilly . # # format.dat for DEC DSP5200S 2GB SCSI disk # disk_type = "DEC DSP5200" \ : ctlr = SCSI \ : cache = 0x11 : trks_zone = 15 : asect = 5 : atrks = 30 \ : ncyl = 2619 : acyl = 2 : pcyl = 2621 : nhead = 21 : nsect = 71 \ : rpm = 3600 : bpt = 36352 partition = "DEC DSP5200" \ : disk = "DEC DSP5200" : ctlr = SCSI \ : a = 0, 32802 : b = 22, 65604 : c = 0, 3904929 : g = 66, 3806523 # Hitachi DK315C-10, DK315C-10, DK315C-11, DK315C-14, DK325C-57, # DK326C-6, DK326C-10, DK515C-78, DK516C-16, DK517C-37 and DK315-14 # entries prepared by Steve Simmons, scs@lokkur.dexter.mi.us. # # These values are taken from a sheet faxed to me by Hitachi. # Cautionary note: the DK315C-14 does *not* fit into a standard # mounting bracket -- the screw holes are in the wrong place. disk_type = "Hitachi DK315C-10" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 1 : atrks = 22 : asect = 1 \ : ncyl = 2467 : acyl = 2 : pcyl = 2469 : nhead = 11 : nsect = 75 \ : rpm = 4500 : bpt = 38912 disk_type = "Hitachi DK315C-11" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 1 : atrks = 30 : asect = 1 \ : ncyl = 2478 : acyl = 2 : pcyl = 2480 : nhead = 15 : nsect = 58 \ : rpm = 4500 : bpt = 30208 disk_type = "Hitachi DK315C-14" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 1 : atrks = 30 : asect = 1 \ : ncyl = 2462 : acyl = 2 : pcyl = 2464 : nhead = 15 : nsect = 75 \ : rpm = 4500 : bpt = 38912 disk_type = "Hitachi DK326C-6" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 1 : atrks = 8 : asect = 1 \ : ncyl = 3200 : acyl = 2 : pcyl = 3202 : nhead = 4 : nsect = 87 \ : rpm = 6300 : bpt = 44544 disk_type = "Hitachi DK326C-10" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 1 : atrks = 14 : asect = 1 \ : ncyl = 3200 : acyl = 2 : pcyl = 3202 : nhead = 7 : nsect = 87 \ : rpm = 6300 : bpt = 44544 disk_type = "Hitachi DK515C-78" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 1 : atrks = 28 : asect = 1 \ : ncyl = 1354 : acyl = 2 : pcyl = 1356 : nhead = 14 : nsect = 69 \ : rpm = 3600 : bpt = 35328 disk_type = "Hitachi DK516C-16" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 1 : atrks = 30 : asect = 1 \ : ncyl = 2170 : acyl = 2 : pcyl = 2172 : nhead = 15 : nsect = 80 \ : rpm = 3600 : bpt = 41472 disk_type = "Hitachi DK517C-37" \ : ctlr = SCSI : fmt_time = 6 \ : trks_zone = 1 : atrks = 42 : asect = 1 \ : ncyl = 3297 : acyl = 2 : pcyl = 3299 : nhead = 21 : nsect = 81 \ : rpm = 5400 : bpt = 41472 # From: MURRAY ALEXANDER W # # This is for a Conner CP3100 (note: not the newer CP30100), an older # full-height 3.5" SCSI drive. disk_type = "CP3100" \ : ctlr = SCSI : fmt_time = 1 \ : ncyl = 1023 : acyl = 2 : pcyl = 1023 : nhead = 4 : nsect = 49 \ : rpm = 3600 : bpt = 25088 partition = "CP3100" \ : disk = "CP3100" : ctlr = SCSI \ : c = 0, 204864 # From: tl@cd.chalmers.se (Torbj|rn Lindgren) # The following format.dat entry is constructed from the Application # Note that accompained our disks. We have run one of these a couple of # days using this entry. M1H and N1H is both documented in the same # AppNote, and even thought it isn't mentioned what the N1H is it MIGHT # be the differential version (both the normal and the wide version). disk_type = "IBM 0664-M1H/N1H" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 2856 : acyl = 2 : pcyl = 2870 \ : nhead = 16 : nsect = 86 : rpm = 5400 : bpt = 57600 # From: Kevin Martinez # Here is format.dat data for Quantum LPS540 and LPS270 drives. Note that # the "Empire 540" is not the same as the LPS540. They are distinguishable # by color: the "Empire" series has black epoxy coat on the base casting; # the LPS series is natural aluminum finish. disk_type = "Quantum LPS 270S" \ :ctlr = SCSI \ :ncyl = 992 : acyl = 2 : pcyl =994 : nhead = 7 : nsect = 76 \ :rpm = 4500 : bpt = 38912 disk_type = "Quantum Empire 1080S" \ :ctlr = SCSI \ :ncyl = 1431 : acyl = 2 : pcyl = 1433 : nhead = 16 : nsect = 92 \ :rpm = 5400 : bpt = 47104 disk_type = "Quantum Empire 540S" \ :ctlr = SCSI \ :ncyl = 1431 : acyl = 2 : pcyl = 1433 : nhead = 8 : nsect = 92 \ :rpm = 5400 : bpt = 47104 # # 940511 shj@dknet.dk, partly courtesy of scsiinfo. # IBM 0664 M1H, ~2 gb, tested on a Sparc IPC running SunOS 4.1.3. disk_type = "IBM OEM 0664M1H" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : atrks = 0 : asect = 34 \ : ncyl = 2787 : acyl = 2 : pcyl = 2857 : nhead = 15 : nsect = 94 \ : rpm = 5400 : bpt = 55272 # From: Daniel Curry # What I was looking for was the geometry for a Seagate ST3600N disk. # Here is what scsiinfo printed out. # disk_type = "SEAGATE ST3600N" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 7 : atrks = 14 : asect = 7 \ : ncyl = 1853 : acyl = 2 : pcyl = 1872 : nhead = 7 : nsect = 79 \ : rpm = 4467 : bpt = 46452 partition = "SEAGATE ST3600N" \ : disk = "SEAGATE ST3600N" : ctlr = SCSI \ : c = 0, 1024709 # From: Mark Tearle # Here's my format.dat submission for the NEC 2352 disk drive, the numbers # of sectors per track (nsect) and bytes per sector (bps) vary a lot # depending on what position the dip switches are in. This is controlled # by 10 switch DIP switch, my dip switches are in the following positions: # 8,9,10,2,3,7 off 1,4,5,6 on # disk_type = "NEC-D2352" \ : ctlr = XD7053 \ : ncyl = 758 : acyl = 2 : pcyl = 760 : nhead = 19 : nsect = 57 \ : rpm = 3070 : bpt = 36288 : bps = 636 # From: "richard a. reitmeyer" # # I called someone here and asked them to try and dial the micropolis # BBS for me and look for the 4110, Here's what I'm told: # disk_type = "Micropolis 4110" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 1998 : acyl = 3 : pcyl = 2428 : nhead = 9 \ : nsect = 114 : rpm = 5400 : bpt = 51718 : trks_zone = 9 \ : atrks = 27 : asect = 6 # From: Paul Brand, Hong Kong (CIS 100267,3526) using scsiinfo 3.3 # The QUANTUM PD1050iS seems to be different from the QUANTUM PD1050S. # (I'm not sure: for instance, for the "Seagate ST11200N" I received from # several people 3 different format.dat entries. Then I discovered this # big format.dat file: entry #4. Scsiinfo gave me a 5th different version.) # disk_type = "QUANTUM PD1050iS" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 12 : atrks = 0 : asect = 2 \ : ncyl = 1859 : acyl = 2 : pcyl = 2448 : nhead = 12 : nsect = 92 \ : rpm = 3600 : bpt = 54096 partition = "QUANTUM PD1050iS" \ : disk = "QUANTUM PD1050iS" : ctlr = SCSI \ : c = 0, 2052336 # From: rsm@math.utexas.edu (Robert S. Maier) # # Entry partially from scsiinfo, partially from information from Quantum # disk_type = "QUANTUM LPS540S" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 4 : atrks = 0 : asect = 2 \ : ncyl = 2113 : acyl = 2 : pcyl = 2740 : nhead = 4 : nsect = 125 \ : rpm = 4500 : bpt = 73500 # # From: huesler@hifo.unizh.ch # # This is based on a list from morrow@cns.ucalgary.ca and adapted # to Fujitsu specifications # "Fujitsu M2512A v2" applies to 230 MB MOs # "Fujitsu M2512A small" applies to 128 MB MOs # ncyl and pcyl could be increased # disk_type = "Fujitsu M2512A v2" \ : ctlr = SCSI : fmt_time = 12 \ : ncyl = 17840 : acyl = 2 : pcyl = 17842 : nhead = 1 : nsect = 25 \ : rpm = 3600 : bpt = 12800 partition = "Fujitsu M2512A v2" \ :disk = "Fujitsu M2512A v2" : ctlr = SCSI \ : a = 0, 0 : b = 0, 0 : c = 0, 446000 : g = 0, 0 disk_type = "Fujitsu M2512A small" \ : ctlr = SCSI \ : ncyl = 9950 : acyl = 2 : pcyl = 9952 : nhead = 1 : nsect = 25 \ : rpm = 3600 : bpt = 12800 partition = "Fujitsu M2512A small" \ : disk = "Fujitsu M2512A small" : ctlr = SCSI \ : a = 0, 0 : b = 0, 0 : c = 0, 248750 : g = 0, 0 # From: Daniel Curry # Derived using scsiinfo 3.3. # disk_type = "SEAGATE ST11950N" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 15 : asect = 6 \ : ncyl = 2715 : acyl = 2 : pcyl = 2707 : nhead = 15 : nsect = 81 \ : rpm = 7200 : bpt = 47628 partition = "SEAGATE ST11950N" \ : disk = "SEAGATE ST11950N" : ctlr = SCSI \ : c = 0, 3298725 disk_type = "CONNER CP3500-540MB-3.5" \ : ctlr = SCSI : fmt_time = 2 \ : atrks = 0 \ : ncyl = 1768 : acyl = 2 : pcyl = 1807 : nhead = 12 : nsect = 50 \ : rpm = 3600 : bpt = 29400 partition = "CONNER CP3500-540MB-3.5" \ : disk = "CONNER CP3500-540MB-3.5" : ctlr = SCSI \ : c = 0, 1060800 # # From: D Andrew Reynhout # # These entries are from Hewlett Packard or distributors, with some # adjustments, and have been tested on SPARCstation10s and 20s. # disk_type = "Hewlett Packard C3323A" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 2995 : acyl = 2 : pcyl = 2997 \ : nhead = 7 : nsect = 98 \ : rpm = 5400 : bpt = 59232 disk_type = "Hewlett Packard C2490A" \ : ctlr = SCSI : fmt_time = 17 \ : trks_zone = 3146 : asect = 0 : atrks = 198 \ : ncyl = 2159 : acyl = 2 : pcyl = 2582 \ : nhead = 18 : nsect = 107 \ : rpm = 6400 : bpt = 55296 # # From brian@canet.ca (Brian Dickson) # # Params courtesy of Open Storage Solutions except for # bpt, which I set to be the midpoint between the bpt figure for the # inner and outer tracks. # # WARNING!! # Do NOT low-level format Elite 9! # The format program will time out during format, making the drive # unusable! For Solaris 2.3, patch 101788-01 will fix this problem. # disk_type = "Seagate ST410800N Elite 9" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 6087 : acyl = 2 : pcyl = 6089 : nhead = 27 \ : nsect = 108 : rpm = 5400 : bpt = 55300 partition = "Seagate ST410800N Elite 9" \ : disk = "Seagate ST410800N Elite 9" : ctlr = SCSI \ : c = 0, 17749692 # # From: ysyang@pine.IECS.FCU.edu.tw (Yaw-Shang Yang) # # I got this table by scsiinfo 3.3 and used it in SPARCstation10s for # three weeks. # disk_type = "QUANTUM EMPIRE_2100S" \ : ctlr = SCSI : fmt_time = 5 \ : trks_zone = 12 : atrks = 0 : asect = 4 \ : ncyl = 2497 : acyl = 2 : pcyl = 3053 : nhead = 12 : nsect = 137 \ : rpm = 5400 : bpt = 80556 partition = "QUANTUM EMPIRE_2100S" \ : disk = "QUANTUM EMPIRE_2100S" : ctlr = SCSI \ : c = 0, 4105068 # From: weitzel@burke.com (David Weitzel) # disk_type = "SEAGATE ST31200N" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 9 : atrks = 18 : asect = 9 \ : ncyl = 2692 : acyl = 2 : pcyl = 2700 : nhead = 9 : nsect = 85 \ : rpm = 5411 : bpt = 49980 # From: Benjamin Lutch # # Micropolis 1991 Drive Geometry disk_type = "MICROPOLIS 1991-27" \ : ctlr = SCSI : fmt_time = 9 \ : ncyl = 4400 : acyl = 2 : pcyl = 4402 : nhead = 27 : nsect = 149 \ : rpm = 5400 : bpt = 23417 # Micropolis 3243 Drive Geometry disk_type = "MICROPOLIS 3243-19" \ : ctlr = SCSI : fmt_time = 9 \ : ncyl = 4139 : acyl = 2 : pcyl = 4141 \ : nhead = 19 : nsect = 106 : rpm = 7200 : bpt = 63282 # Micropolis 4110AV Drive Geometry disk_type = "MICROPOLIS 4110-09" \ : ctlr = SCSI : fmt_time = 9 \ : ncyl = 2283 : acyl = 2 : pcyl = 2485 \ : nhead = 9 : nsect = 95 : rpm = 5400 : bpt = 56715 # From: "rune.johansen" # # 1 GB Starfire (2199878) disk_type = "IBM DFHSS1x" \ : ctlr = SCSI : ncyl = 4383 : acyl = 2 : pcyl = 4385 \ : nhead = 4 : nsect = 125 : rpm = 7200 : bpt = 0 # 2 GB Starfire (4404489) disk_type = "IBM DFHSS2x" \ : ctlr = SCSI : ncyl = 4388 : acyl = 2 : pcyl = 4390 \ : nhead = 8 : nsect = 125 : rpm = 7200 : bpt = 0 # 4 GB Starfire (8813870) disk_type = "IBM DFHSS4x" \ : ctlr = SCSI : ncyl = 4390 : acyl = 2 : pcyl = 4392 \ : nhead = 16 : nsect = 125 : rpm = 7200 : bpt = 0 # 4 GB Allicat disk_type = "IBM 0664CSH" \ : ctlr = SCSI : ncyl = 2787 : acyl = 2 : pcyl = 2789 \ : nhead = 30 : nsect = 125 : rpm = 5400 : bpt = 58024 # 2 GB Allicat disk_type = "IBM 0664M1H" \ : ctlr = SCSI : ncyl = 2787 : acyl = 2 : pcyl = 2789 \ : nhead = 15 : nsect = 94 : rpm = 5400 : bpt = 58024 # 1 GB Spitfire disk_type = "IBM 0662S12" \ : ctlr = SCSI : ncyl = 3803 : acyl = 2 : pcyl = 3805 \ : nhead = 5 : nsect = 108 : rpm = 5400 : bpt = 0 # 270 MB Satsuma disk_type = "IBM DSAS-3270" \ : ctlr = SCSI : ncyl = 2542 : acyl = 2 : pcyl = 2544 \ : nhead = 2 : nsect = 108 : rpm = 4500 : bpt = 59400 # 360 MB Satsuma disk_type = "IBM DSAS-3360" \ : ctlr = SCSI : ncyl = 3297 : acyl = 2 : pcyl = 3299 \ : nhead = 2 : nsect = 108 : rpm = 4500 : bpt = 59400 # 540 MB Satsuma disk_type = "IBM DSAS-3540" \ : ctlr = SCSI : ncyl = 3259 : acyl = 2 : pcyl = 3261 \ : nhead = 3 : nsect = 108 : rpm = 4500 : bpt = 59400 # 720 MB Satsuma disk_type = "IBM DSAS-3720" \ : ctlr = SCSI : ncyl = 3292 : acyl = 2 : pcyl = 3294 \ : nhead = 4 : nsect = 108 : rpm = 4500 : bpt = 59400 # From: Peter Coleman # # I have received the following from Open Storage Solutions disk_type = "Seagate ST15150N" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 5119 : acyl = 2 : pcyl = 5121 : nhead = 21 : nsect = 78 \ : rpm = 7200 : bpt = 64773 partition = "Seagate ST15150N" \ : disk = "Seagate ST15150N" : ctlr = SCSI \ : c = 0, 8384922 # From: troy@big.att.com (Troy Cauble) # # This was generated by scsiinfo, except the bpt number # which was taken from the manual. # Seagate, 2.1G, tested on Sparc 20 running SunOS 4.1.4 # disk_type = "SEAGATE ST32550N" \ : ctlr = SCSI : fmt_time = 5 \ : trks_zone = 11 : atrks = 22 : asect = 9 \ : ncyl = 3495 : acyl = 2 : pcyl = 3511 : nhead = 11 : nsect = 109 \ : rpm = 7200 : bpt = 64160 partition = "SEAGATE ST32550N" \ : disk = "SEAGATE ST32550N" : ctlr = SCSI \ : c = 0, 4190505 # From: derekt@stpaul.gov (Derek Terveer) # # This is a 5.25" r/w optical drive with 600MB, 512b/sector # platters. With standard 10% reserve, gives 269,533 KB per # side. # disk_type = "RICOH RO-5031E" \ : ctlr = SCSI : fmt_time = 1 \ : trks_zone = 15 : atrks = 45 : asect = 8 \ : ncyl = 710 : acyl = 2 : pcyl = 1632 : nhead = 15 : nsect = 54 \ : rpm = 3600 : bpt = 31752 partition = "RICOH RO-5031E" \ : disk = "RICOH RO-5031E" : ctlr = SCSI \ : c = 0, 575100 # From: jude@nas.nasa.gov (Jude George) # disk_type = "Quantum Lightning 730S" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 1415 : acyl = 2 : pcyl = 1416 : nhead = 16 : nsect = 63 \ : rpm = 4500 : bpt = 32221 # a=80,640KB; b=48,384KB; g=584,186KB partition = "Quantum Lightning 730S" \ : disk = "Quantum Lightning 730S" : ctlr = SCSI \ : a = 0, 161280 : b = 160, 96768 : c = 0, 1426320 : g = 256, 1168272 # # From: Georg Chytil # # The parameters were constructed using output from the Adaptec tools, # scsiinfo ( Thanks to cliffa@ray.abo.fi for the hint ) and a fax I got # from the distributor to aid me formatting it on AIX ... # IBM Starfire DFHSS2F 2.25 GB # disk_type = "IBM OEM DFHSS2F" \ : ctlr = SCSI : fmt_time = 5 \ : trks_zone = 8 : atrks = 0 : asect = 19 \ : ncyl = 4076 : acyl = 2 : pcyl = 4390 : nhead = 8 : nsect = 135 \ : rpm = 7200 : bpt = 79380 partition = "IBM OEM DFHSS2F" \ : disk = "IBM OEM DFHSS2F" : ctlr = SCSI \ : a = 0, 4100760 \ : b = 3797, 301320 # # From: "Kaja P. Christiansen" # Seagate Hawk 4GB # I looked at the geometry with scsiinfo. # disk_type = "SEAGATE ST15230N" \ : ctlr = SCSI : fmt_time = 9 \ : trks_zone = 19 : atrks = 38 : asect = 12 \ : ncyl = 3974 : acyl = 2 : pcyl = 3992 : nhead = 19 : nsect = 111 \ : rpm = 5411 : bpt = 57856 partition = "SEAGATE ST15230N" \ : disk = "SEAGATE ST15230N" : ctlr = SCSI \ : c = 0, 8381166 # # From: diekema@linus.si.com (Jon Diekema) # disk_type = "Fujitsu-M2651SA" \ : ctlr = SCSI : fmt_time = 4 \ : ncyl = 1934 : acyl = 2 : pcyl = 1944 : nhead = 16 : nsect = 88 \ : rpm = 5400 : bpt = 52864 partition = "Fujitsu-M2651SA" \ : disk = "Fujitsu-M2651SA" : ctlr = SCSI \ : c = 0, 2723072 disk_type = "Micropolis 4221" \ : ctlr = SCSI \ : ncyl = 4079 : acyl = 2 : pcyl = 4081 : nhead = 9 : nsect = 109 \ : rpm = 7200 : bpt = 65073 : fmt_time = 3 partition = "Micropolis 4221" \ : disk = "Micropolis 4221" : ctlr = SCSI \ : a = 0, 4001499 : c = 0, 4001499 # From: joabr@uhura.imt.liu.se (Joakim Brandberg) # This is an entry for Quantum's ATLAS 2.1 Gbyte disk disk_type = "Quantum XP32150" \ : ctlr = SCSI : fmt_time = 5 \ : trks_zone = 10 : atrks = 0 : asect = 10 \ : ncyl = 3850 : acyl = 2 : pcyl = 3907 : nhead = 10 : nsect = 109 \ : rpm = 7200 : bpt = 64092 # From: hannu@fincitec.fi (Hannu Juopperi) # I got this from Edward C. Zimmermann disk_type = "MICROP 4221-09MZ 10204" \ : ctlr = SCSI : fmt_time = 5 \ : trks_zone = 9 : atrks = 27 : asect = 6 \ : ncyl = 3198 : acyl = 2 : pcyl = 4048 : nhead = 9 : nsect = 139 \ : rpm = 7200 : bpt = 81732 partition = "MICROP 4221-09MZ 10204" \ : disk = "MICROP 4221-09MZ 10204" : ctlr = SCSI \ : c = 0, 4000698 # From: diekema@linus.si.com (Jon Diekema) # disk_type = "SEAGATE ST31230N" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 5 : atrks = 10 : asect = 5 \ : ncyl = 3978 : acyl = 2 : pcyl = 3992 : nhead = 5 : nsect = 104 \ : rpm = 5411 : bpt = 61152 partition = "SEAGATE ST31230N" \ : disk = "SEAGATE ST31230N" : ctlr = SCSI \ : c = 0, 2068560 # From: frueh@astro.as.utexas.edu (Marian Frueh) # We've just installed a DEC disk on our SUN system. Here's the info provided # by the company. # disk_type = "DEC DSP3107L" \ : ctlr = SCSI : fmt_time = 9 \ : ncyl = 3147 : acyl = 2 : pcyl = 3149 : nhead = 8 : nsect = 83 \ : rpm =5400 : bpt = 49551 partition = "DEC DSP3107L" \ : disk = "DEC DSP3107L" : ctlr = SCSI \ : c= 0, 2089608 # # From: "Kaja P. Christiansen" # QUANTUM XP34301 # disk_type = "QUANTUM XP34301" \ : ctlr = SCSI : fmt_time = 9 \ : trks_zone = 20 : atrks = 0 : asect = 10 \ : ncyl = 3561 : acyl = 2 : pcyl = 4076 : nhead = 20 : nsect = 118 \ : rpm = 7200 : bpt = 69384 partition = "QUANTUM XP34301" \ : disk = "QUANTUM XP34301" : ctlr = SCSI \ : c = 0, 8403960 # From: Daniel Curry # generated using scsiinfo. # disk_type = "CONNER CFP4207S 4.28GB" \ : ctlr = SCSI : fmt_time = 9 \ : atrks = 0 \ : ncyl = 3353 : acyl = 2 : pcyl = 3999 : nhead = 20 : nsect = 125 \ : rpm = 7200 : bpt = 73500 partition = "CONNER CFP4207S 4.28GB" \ : disk = "CONNER CFP4207S 4.28GB" : ctlr = SCSI \ : c = 0, 8382500 # From: busa057@cantua.canterbury.ac.nz (Tristram Scott) # here is a format.dat entry I made with help from scsiinfo. I am using # this IBM DPES-31080 1 Gb drive on a Sparc1 under SunOS 4.1.3. # disk_type = "IBM DPES-31080" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 484 : atrks = 8 : asect = 50 \ : ncyl = 4901 : acyl = 2 : pcyl = 4903 : nhead = 4 : nsect = 108 \ : rpm = 5400 : bpt = 63504 partition = "IBM DPES-31080" \ : disk = "IBM DPES-31080" : ctlr = SCSI \ : c = 0, 2117232 # # From: garcia@f18sunc.chinalake.navy.mil (Mike Garcia) # I received this from Conner's FAX-back service. # disk_type = "Conner CFP1060" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 1 : asect = 1 \ : ncyl = 2329 : acyl = 2 : pcyl = 2756 : nhead = 8 : nsect=111 \ : rpm=5400 : bpt=57344 partition = "Conner CFP1060" \ : disk = "Conner CFP1060" : ctlr = SCSI \ : c = 0, 2068152 # From: andrew.reynhout@analog.com (D Andrew Reynhout) # # Hewlett Packard C3725S / SureStore 2000LP # Values are from HP or by calculation. # disk_type = "Hewlett Packard C3725S" \ : ctlr = SCSI : fmt_time = 5 \ : trks_zone = 20003 : atrks = 819 : asect = 0 \ : ncyl = 3362 : acyl = 2 : pcyl = 3703 \ : nhead = 9 : nsect = 140 : rpm = 5400 \ : bpt = 75953 partition = "Hewlett Packard C3725S" \ : disk = "Hewlett Packard C3725S" : ctlr = SCSI \ : c = 0, 4236120 : h = 1, 4193280 # From: woods@most.weird.com (Greg A. Woods) # # I'm not 100% sure on the bpt value, but otherwise it seems to work..... # disk_type = "Maxtor XT-3280S" \ : ctlr = SCSI \ : cache = 0x0: trks_zone = 15 : atrks = 2 : asect = 2 \ : ncyl = 1222 : acyl = 2 : pcyl = 1224 : nhead = 15 : nsect = 25 \ : rpm = 3600 : bpt = 16896 # From: Jonathan Thornburg # # Information from Ian D Watt, Fujitsu Canada, (905)602-5454 x349, # except for bpt from scsiinfo -F # disk_type = "Fujitsu M2684S" \ : ctlr = SCSI : ncyl = 2338 : acyl = 2 : pcyl = 2340 \ : nhead = 6 : nsect = 74 : rpm = 4500 : bpt = 43512 # From: Yaw-Shang Yang # Derived using scsiinfo 3.3 # disk_type = "QUANTUM FIREBALL1080S" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 4 : atrks = 0 \ : ncyl = 3836 : acyl = 2 : pcyl = 3835 : nhead = 4 : nsect = 139 \ : rpm = 5400 : bpt = 81732 partition = "QUANTUM FIREBALL1080S" \ : disk = "QUANTUM FIREBALL1080S" : ctlr = SCSI \ : c = 0, 2132816 # From: grosch@ichips.intel.com # # This is the replacement for the ST11200N that Seagate used to ship. # disk_type = "Seagate ST51080N" \ : ctlr = SCSI : ncyl = 4824 : acyl = 2 : pcyl = 4826 \ : nhead = 4 : nsect = 109 : rpm = 5376 : bpt = 32356 # # from http://www.iomega.com # disk_type = "Zip 100" \ : ctlr = SCSI \ : ncyl = 2406 : acyl = 2 : pcyl = 2408 : nhead = 2 \ : nsect = 40 : rpm = 3600 : bpt = 20480 partition = "Zip 100" \ : disk = "Zip 100" : ctlr = SCSI \ : c = 0,192480 disk_type = "Iomega 230" \ : ctlr = SCSI \ : ncyl = 5591 : acyl = 2 : pcyl = 5593 : nhead = 2 \ : nsect = 40 : rpm = 3600 : bpt = 20480 partition = "Iomega 230" \ : disk = "Iomega 230" : ctlr = SCSI \ : c = 0,447280 # # From: rlesh@keyway.net (Rick Lesh) # disk_type = "CONNER CFP2105S 2.147G" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 1 : asect = 1 \ : ncyl = 3015 : acyl = 2 : pcyl = 3940 : nhead = 10 : nsect = 139 \ : rpm = 5400 : bpt = 71168 partition = "CONNER CFP2105S 2.147G" \ : disk = "CONNER CFP2105S 2.147G" : ctlr = SCSI \ : c = 0, 4190850 # From: deh@atype.com (David Hollingsworth) # Quantum Saturn VP32170S info obtained using scsiinfo-4.2 disk_type = "Quantum VP32170" \ : ctlr = SCSI : fmt_time = 5 \ : trks_zone = 10 : atrks = 0 : asect = 10 \ : ncyl = 3444 : acyl = 2 : pcyl = 3907 : nhead = 10 : nsect = 123 \ : rpm = 5403 : bpt = 72324 partition = "Quantum VP32170" \ : disk = "Quantum VP32170" : ctlr = SCSI \ : c = 0, 4236120 # From: simes@tcp.co.uk (Simon Burr) # The following is the format.dat entry for an IOMega Jaz drive. disk_type = "Jaz 1GB" \ : ctlr = SCSI : ncyl = 1018 : acyl = 2 : pcyl = 1020 \ : nhead = 64 : nsect = 32 : rpm = 3600 : bpt = 16384 partition = "Jaz 1GB" \ : disk = "Jaz 1GB" : ctlr = SCSI \ : c = 0, 2084864 # From: "Gregory J. Sandell" # Fujitsu M2934S (or M2934SA or M2934SA_512) # I cooked a format entry up from the specs and a little guesswork and # here's what I came up with. It worked when I formatted my drive under # SunOS 4.1.3. disk_type = "Fujitsu-M2934S" \ : ctlr = SCSI \ : ncyl = 3551 : acyl = 2 : pcyl = 3553 : nhead = 18 : nsect = 133 \ : rpm = 7200 : bpt = 68096 # From: "Kaja P. Christiansen" # Quantum-XP34300-81HB (4G disk) # disk_type = "Quantum-XP34300-81HB" \ : ctlr = SCSI : ncyl = 3850 : acyl = 2 : pcyl = 3852 \ : nhead = 20 : nsect = 109 : rpm = 7200 : bpt = 55808 partition = "Quantum-XP34300-81HB" \ : disk = "Quantum-XP34300-81HB" : ctlr = SCSI \ : c = 0, 8393000 # From: "Alexander Horn" # The following four entries were generated by scsiinfo # IBM DFRSS4F, 4.320G, tested on a SPARCstation-2 running SunOS 4.1.2 disk_type = "IBM DFRSS4F" \ : ctlr = SCSI : fmt_time = 9 \ : trks_zone = 16 : atrks = 0 : asect = 37 \ : ncyl = 4078 : acyl = 2 : pcyl = 4392 : nhead = 16 : nsect = 135 \ : rpm = 7200 : bpt = 79380 partition = "IBM DFRSS4F" \ : disk = "IBM DFRSS4F" : ctlr = SCSI \ : c = 0, 8808480 # DEC DSP5200S (Version T366), 2G, # tested on a SPARCstation-2 running SunOS 4.1.2 disk_type = "DEC DSP5200S" \ : ctlr = SCSI : fmt_time = 4 \ : trks_zone = 21 : atrks = 0 : asect = 21 \ : ncyl = 2618 : acyl = 2 : pcyl = 2621 : nhead = 21 : nsect = 71 \ : rpm = 3600 : bpt = 41748 partition = "DEC DSP5200S" \ : disk = "DEC DSP5200S" : ctlr = SCSI \ : c = 0, 3903438 # SEAGATE ST43400N, 3.5G, tested on a SPARCstation-2 running SunOS 4.1.2 disk_type = "SEAGATE ST43400N" \ : ctlr = SCSI : fmt_time = 6 \ : cache = 0x21 : trks_zone = 21 : asect = 9 \ : ncyl = 2734 : acyl = 2 : pcyl = 2737 : nhead = 21 : nsect = 99 \ : rpm = 5400 : bpt = 58212 partition = "SEAGATE ST43400N" \ : disk = "SEAGATE ST43400N" : ctlr = SCSI \ : c = 0, 5683986 # Quantum Fireball 1080S, 1G, tested on a SPARCstation-2 running SunOS 4.1.2 disk_type = "QUANTUM FIREBALL1080S" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 4 : atrks = 0 \ : ncyl = 3836 : acyl = 2 : pcyl = 3835 : nhead = 4 : nsect = 139 \ : rpm = 5400 : bpt = 81732 partition = "QUANTUM FIREBALL1080S" \ : disk = "QUANTUM FIREBALL1080S" : ctlr = SCSI \ : c = 0, 2132816 # From: "Kaja P. Christiansen" # Micropolis 4421-II disk_type = "MICROP 4421-07" \ : ctlr = SCSI : fmt_time = 9 : rpm = 5400 \ : ncyl = 3459 : acyl = 3 : pcyl = 4049 \ : nhead = 7 : nsect = 173 : bpt = 87552 partition = "MICROP 4421-07" \ : disk = "MICROP 4421-07" : ctlr = SCSI \ : c = 0, 4188849 # From: Francesco Messineo # The entry has been taken using scsiinfo under SunOS 4.1.4 on a # sparc 1 host. disk_type = "QUANTUM TRB850S" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 4 : atrks = 0 \ : ncyl = 2941 : acyl = 2 : pcyl = 3653 : nhead = 4 : nsect = 141 \ : rpm = 3600 : bpt = 82908 # From: pauloh@inf.puc-rio.br (Paulo Henrique Schindler) # I've bought a Seagate ST34371N and installed it # in a Axil 320 with SunOS 4.1.4. To find the entry in format.dat # I used the scsiinfo 4.1 utility: scsiinfo -F /dev/rsd3c. # (bpt from Western Scientific, courtesy of Tom Schaefer ) disk_type = "SEAGATE ST34371N" \ : ctlr = SCSI : fmt_time = 9 \ : trks_zone = 80 : atrks = 0 : asect = 80 \ : ncyl = 5147 : acyl = 2 : pcyl = 5168 : nhead = 10 : nsect = 165 \ : rpm = 7228 : bpt = 84480 partition = "SEAGATE ST34371N" \ : disk = "SEAGATE ST34371N" : ctlr = SCSI \ : c = 0, 8492550 # From: Volker Borchert # All info by scsiinfo-4.3. # It seems the C3323-300 is different from the C3323A described by # Andrew Reynhout (note pcyl): disk_type = "HP C3323-300" \ : ctlr = SCSI : fmt_time = 3 \ : trks_zone = 6723 : atrks = 490 : asect = 0 \ : ncyl = 2445 : acyl = 2 : pcyl = 2982 : nhead = 7 : nsect = 120 \ : rpm = 5400 : bpt = 70560 partition = "HP C3323-300" \ : disk = "HP C3323-300" : ctlr = SCSI \ : c = 0, 2053800 # From: Volker Borchert # Geometry information retrieved by scsiinfo. disk_type = "QUANTUM FIREBALL_TM3200S" \ : ctlr = SCSI : fmt_time = 7 \ : trks_zone = 5 : atrks = 0 : asect = 2 \ : ncyl = 7899 : acyl = 2 : pcyl = 6810 : nhead = 5 : nsect = 159 \ : rpm = 4500 : bpt = 93492 partition = "QUANTUM FIREBALL_TM3200S" \ : disk = "QUANTUM FIREBALL_TM3200S" : ctlr = SCSI \ : c = 0, 6279705 # From: stephane@lituus.fr (Stephane Legrand) # This entry is based on scsiinfo and the entry for the Fujitsu-M2934S. disk_type = "FUJITSU M2932S-512" \ : ctlr = SCSI \ : ncyl = 3419 : acyl = 2 : pcyl = 3421 : nhead = 9 : nsect = 133 \ : rpm = 7200 : bpt = 68096 : trks_zone = 9 : asect = 5 partition = "FUJITSU M2932S-512" \ : disk = "FUJITSU M2932S-512" : ctlr = SCSI \ : c = 0, 4092543 # From: Guenter Millahn disk_type = "IBM-DCAS-34330-S60B" \ : ctlr = SCSI : ncyl = 8203 : acyl = 2 : pcyl = 8205 \ : nhead = 6 : nsect = 171 : rpm = 5400 partition = "IBM-DCAS-34330-S60B" \ : disk = "IBM-DCAS-34330-S60B" : ctlr = SCSI \ : 2 = 0, 8416278 # From: Tim Gilbert (gilbert@marin.cc.ca.us) # This is pulled off of quantum's page on Sun format parameters, at # http://www.quantum.com/appnotes/sun.htm as of 5/9/97. disk_type = "Quantum-Fireball_TM1280" \ : ctlr = SCSI : ncyl = 4133 : acyl = 2 : pcyl = 4135 : nhead = 4 \ : nsect = 139 : rpm = 4500 disk_type = "Quantum-Fireball_TM2110S" \ : ctlr = SCSI : ncyl = 6483 : acyl = 2 : pcyl = 6485 : nhead = 4 \ : nsect = 159 : rpm = 4500 # From: bt@teknon.de (Volker Borchert) # derived from scsiinfo 4.3 disk_type = "FUJITSU M2624F-512" \ : ctlr = SCSI : fmt_time = 2 \ : trks_zone = 11 : asect = 3 \ : ncyl = 1463 : acyl = 2 : pcyl = 1429 : nhead = 11 : nsect = 63 \ : rpm = 4398 : bpt = 37044 partition = "FUJITSU M2624F-512" \ : disk = "FUJITSU M2624F-512" : ctlr = SCSI \ : c = 0, 1013859 # From: bt@teknon.de (Volker Borchert) disk_type = "FUJITSU M2681S-512" \ : ctlr = SCSI : fmt_time = 1 \ : trks_zone = 3 : asect = 3 \ : ncyl = 2322 : acyl = 2 : pcyl = 2380 : nhead = 3 : nsect = 74 \ : rpm = 4500 : bpt = 43512 partition = "FUJITSU M2681S-512" \ : disk = "FUJITSU M2681S-512" : ctlr = SCSI \ : c = 0, 515484 # From: "Marc L. Summers-SysAdmin" # I got a FAX from Andataco here is the data: # Quantum XP39100AL W/WC/WD, Andataco PN: 910S3 disk_type = "QUANTUM XP39100" \ : ctlr = SCSI : fmt_time = 9 \ : ncyl = 5847 : acyl = 2 : pcyl = 5849 : nhead = 20 : nsect = 152 \ : rpm = 7200 : bpt = 93176 # From: David_Gunn@lardav.com (David Gunn) # I obtained the entry from Artecon: disk_type = "Arte Conner CFP2107S" \ : ctlr = "SCSI" \ : ncyl = 3380 : acyl = 2 : pcyl = 3999 : nhead = 10 : nsect = 124 \ : rpm = 7200 : bpt = 63488 partition = "Arte Conner CFP2107S" \ : disk = "Arte Conner CFP2107S" : ctlr = SCSI \ : c = 0, 4191200 # From: jsprech@melpar.esys.com (Joel Sprechman) # Western Digitals new Enterprise SCSI line of drives disk_type="WDIGTL ENTERPRI 2170" \ : ctlr = SCSI : fmt_time = 9 \ : ncyl = 5747 : acyl = 2 : pcyl = 5749 : nhead = 4 : nsect = 185\ : rpt = 7200 : bpt = 110445 partition = "WDIGTL ENTRPRI 2170" \ : disk = "WDIGTL ENTRPRI 2170" : ctlr = SCSI \ : c = 0,4252780